Chip 1998 September/CHIP Eylül 1998.iso/Slackwar/docs/Disk-HOWTO

Text File | 1997-11-14 | 166KB | 3,558 lines

  Linux Disk HOWTO
  Stein Gjoen, [e-mail]
  v0.16d, 9 November 1997

  This document describes how best to use multiple disks and partitions
  for a Linux system. Although some of this text is Linux specific the
  general approach outlined here can be applied to many other multi
  tasking operating systems.

  1.  Introduction

  In commemoration of recent legal development this brand new release is
  code named the Trademark Resolution release.

  New code names will appear as per industry standard guidelines to
  emphasize the state-of-the-art-ness of this document.

  This document was written for two reasons, mainly because I got hold
  of 3 old SCSI disks to set up my Linux system on and I was pondering
  how best to utilise the inherent possibilities of parallelizing in a
  SCSI system. Secondly I hear there is a prize for people who write
  documents...

  This is intended to be read in conjunction with the Linux Filesystem
  Structure Standard (FSSTND). It does not in any way replace it but
  tries to suggest where physically to place directories detailed in the
  FSSTND, in terms of drives, partitions, types, RAID, file system (fs),
  physical sizes and other parameters that should be considered and
  tuned in a Linux system, ranging from single home systems to large
  servers on the Internet.

  Even though it is now more than a year since last release of the
  FSSTND work is still continuing, under a new name, and will encompass
  more than Linux, fill in a few blanks hinted at in FSSTND version 1.2
  as well as other general improvements. The development mailing list is
  currently private but a general release is hopefully in the near
  future. The new issue will be named Filesystem Hierarchy Standard
  (FHS) and will cover more than Linux alone.

  It is also a good idea to read the Linux Installation guides
  thoroughly and if you are using a PC system, which I guess the
  majority still does, you can find much relevant and useful information
  in the FAQs for the newsgroup comp.sys.ibm.pc.hardware especially for
  storage media.

  This is also a learning experience for myself and I hope I can start
  the ball rolling with this Mini-HOWTO and that it perhaps can evolve
  into a larger more detailed and hopefully even more correct HOWTO.

  First of all we need a bit of legalese. Recent development shows it is
  quite important.

  1.1.  Copyright

  This HOWTO is copyrighted 1996 Stein Gjoen.

  Unless otherwise stated, Linux HOWTO documents are copyrighted by
  their respective authors. Linux HOWTO documents may be reproduced and
  distributed in whole or in part, in any medium physical or electronic,
  as long as this copyright notice is retained on all copies. Commercial
  redistribution is allowed and encouraged; however, the author would
  like to be notified of any such distributions.

  All translations, derivative works, or aggregate works incorporating
  any Linux HOWTO documents must be covered under this copyright notice.
  That is, you may not produce a derivative work from a HOWTO and impose
  additional restrictions on its distribution. Exceptions to these rules
  may be granted under certain conditions; please contact the Linux
  HOWTO coordinator at the address given below.

  In short, we wish to promote dissemination of this information through
  as many channels as possible. However, we do wish to retain copyright
  on the HOWTO documents, and would like to be notified of any plans to
  redistribute the HOWTOs.

  If you have questions, please contact Greg Hankins, the Linux HOWTO
  coordinator, at [e-mail] via email.

  1.2.  Disclaimer

  Use the information in this document at your own risk. I disavow any
  potential liability for the contents of this document. Use of the
  concepts, examples, and/or other content of this document is entirely
  at your own risk.

  All copyrights are owned by their owners, unless specifically noted
  otherwise.  Use of a term in this document should not be regarded as
  affecting the validity of any trademark or service mark.

  Naming of particular products or brands should not be seen as
  endorsements.

  You are strongly recommended to take a backup of your system before
  major installation and backups at regular intervals.

  1.3.  News

  The most recent addition is a new section on how best to get help
  should you find yourself unable to solve your problems as well as more
  suggestion on maintenance.

  Due to an enormous amount of spam I have been forced to mangle all e-
  mail addresses herein in order to fool the e-mail harvesters that scan
  through the net for victims to be put on the lists. Feedbeck tells me
  some damage has already happened, this is very unfortunate.  Mangiling
  is done by replacing the @ character with  (at)

  A number of pointers to relevant mailing lists are also added.

  Since the 0.14 version was released there have been too many changes
  to list here. I have received much input and a substantial patch from
  kris (at) koentopp.de that adds many new details.  The document has
  grown a lot, actually beyond expectations.

  I have also upgraded my system to Debian 1.2.6 and have replaced the
  old Slackware values with the Debian values for disk space
  requirements for the various directory. I will use Debian as a base
  for discussions and examples here, though the HOWTO is equally
  applicable to other distributions, even other operating systems. At
  the time of writing this Debian 1.3 is out in beta and will soon be
  used as the test bench for further versions of this document.
  More news: there has been a fair bit of interest in new kinds of file
  systems in the comp.os.linux newsgroups, in particular logging,
  journaling and inherited file systems. Watch out for updates. Projects
  on volume management is also under way. The old defragmentation
  program for ext2fs is being updated and there is continuing interests
  for compression.

  The latest version number of this document can be gleaned from my plan
  entry if you finger <finger:[e-mail]> my Nyx account.

  Also, the latest version will be available on my web space on nyx: The
  Multi Disk System Tuning mini-HOWTO Homepage
  <http://www.nyx.net/~sgjoen/disk.html>.

  A text-only version as well as the SGML source can also be downloaded
  there.  A nicely formatted postscript version is also available now.
  In order to save disk space and bandwidth it has been compressed using
  gzip.

  Also planned is a series of URLs to helpful software referred to in
  this document. A mirror in Europe will be announced soon.

  I have very recently changed jobs, address etc so there will be a few
  delays in updates before I get the time for a more systematic updates.

  From version 0.15 onward this document is primarily handles as an SGML
  document which means future printouts should look nicer than the old
  text based version. This also means that it has more or less grown
  into a full HOWTO. With respect to size it must be admitted it is a
  long time there was anything "mini" about it.

  1.4.  Credits

  In this version I have the pleasure of acknowledging even more people
  who have contributed in one way or another:

       ronnej (at ) ucs.orst.edu
       cm (at) kukuruz.ping.at
       armbru (at) pond.sub.org
       R.P.Blake (at) open.ac.uk
       neuffer (at) goofy.zdv.Uni-Mainz.de
       sjmudd (at) redestb.es
       nat (at) nataa.fr.eu.org
       sundbyk (at) horten.geco-prakla.slb.com
       gjoen (at) sn.no
       mike (at) i-Connect.Net
       roth (at) uiuc.edu
       phall (at) ilap.com
       szaka (at) mirror.cc.u-szeged.hu
       CMckeon (at) swcp.com
       kris (at) koentopp.de
       edick (at) idcomm.com
       pot (at) fly.cnuce.cnr.it

  Special thanks go to nakano (at) apm.seikei.ac.jp for doing the
  Japanese translation <http://jf.linux.or.jp/JF/JF-ftp/other-
  formats/Disk-HOWTO/html/Disk-HOWTO.html>, general contributions as
  well as contributing an example of a computer in an academic setting,
  which is included at the end of this document.

  Not many still, so please read through this document, make a
  contribution and join the elite. If I have forgotten anyone, please
  let me know.

  New in this version is an appendix with a few tables you can fill in
  for your system in order to simplify the design process.

  Any comments or suggestions can be mailed to my mail address on nyx:
  [e-mail].

  So let's cut to the chase where swap and /tmp are racing along hard
  drive...

  2.  Structure

  As this type of document is supposed to be as much for learning as a
  technical reference document I have rearranged the structure to this
  end. For the designer of a system it is more useful to have the
  information presented in terms of the goals of this exercise than from
  the point of view of the logical layer structure of the devices
  themselves. Nevertheless this document would not be complete without
  such a layer structure the computer field is so full of, so I will
  include it here as an introduction to how it works.

  It is a long time since the mini in mini-HOWTO could be defended as
  proper but I am convinced that this document is as long as it needs to
  be in order to make the right design decisions, and not longer.

  2.1.  Logical structure

  This is based on how each layer access each other, traditionally with
  the application on top and the physical layer on the bottom.  It is
  quite useful to show the interrelationship between each of the layers
  used in controlling drives.

               ___________________________________________________________
               |__     File structure          ( /usr /tmp etc)        __|
               |__     File system             (ext2fs, vfat etc)      __|
               |__     Volume management       (AFS)                   __|
               |__     RAID, concatenation     (md)                    __|
               |__     Device driver           (SCSI, IDE etc)         __|
               |__     Controller              (chip, card)            __|
               |__     Connection              (cable, network)        __|
               |__     Drive                   (magnetic, optical etc) __|
               -----------------------------------------------------------

  In the above diagram both volume management and RAID and concatenation
  are optional layers. The 3 lower layers are in hardware.  All parts
  are discussed at length later on in this document.

  2.2.  Document structure

  Most users start out with a given set of hardware and some plans on
  what they wish to achieve and how big the system should be. This is
  the point of view I will adopt in this document in presenting the
  material, starting out with hardware, continuing with design
  constraints before detailing the design strategy that I have found to
  work well.  I have used this both for my own personal computer at
  home, a multi purpose server at work and found it worked quite well.
  In addition my Japanese co-worker in this project have applied the
  same strategy on a server in an academic setting with similar success.

  Finally at the end I have detailed some configuration tables for use
  in your own design. If you have any comments regarding this or notes
  from your own design work I would like to hear from you so this
  document can be upgraded.

  3.  Drive technologies

  A far more complete discussion on drive technologies for IBM PCs can
  be found at the home page of The Enhanced IDE/Fast-ATA FAQ
  <http://thef-nym.sci.kun.nl/~pieterh/storage.html> which is also
  regularly posted on Usenet News.  Here I will just present what is
  needed to get an understanding of the technology and get you started
  on your setup.

  3.1.  Drives

  This is the physical device where your data lives and although the
  operating system makes the various types seem rather similar they can
  in actual fact be very different. An understanding of how it works can
  be very useful in your design work. Floppy drives fall outside the
  scope of this document, though should there be a big demand I could
  perhaps be persuaded to add a little here.

  3.2.  Geometry

  Physically disk drives consists of one or more platters containing
  data that is read in and out using sensors mounted on movable heads
  that are fixed with respects to themselves. Data transfers therefore
  happens across all surfaces simultaneously which defines a cylinder of
  tracks. The drive is also divided into sectors containing a number of
  data fields.

  Drives are therefore often specified in terms of its geometry: the
  number of Cylinders, Heads and Sectors (CHS).

  For various reasons there is now a number of translations between

  ╖  the physical CHS of the drive itself

  ╖  the logical CHS the drive reports to the BIOS or OS

  ╖  the logical CHS used by the OS

  Basically it is a mess and a source of much confusion. For more
  information you are strongly recommended to read the Large Disk mini-
  HOWTO

  3.3.  Media

  The media technology determines important parameters such as
  read/write rates, seek times, storage size as well as if it is
  read/write or read only.

  3.3.1.  Magnetic Drives

  This is the typical read-write mass storage medium, and as everything
  else in the computer world, comes in many flavours with different
  properties. Usually this is the fastest technology and offers
  read/write capability. The platter rotates with a constant angular
  velocity (CAV) with a variable physical sector density for more
  efficient magnetic media area utilisation.  In other words, the number
  of bits per unit length is kept roughly constant by increasing the
  number of logical sectors for the outer tracks.

  Typical values for rotational speeds are 4500 and 5400 rpm, though
  7200 is also used. Very recently also 10000 rpm has entered the mass
  market.  Seek times are around 10ms, transfer rates quite variable
  from one type to another but typically 4-40 MB/s.  With the extreme
  high performance drives you should remember that performance costs
  more electric power which is dissipated as heat, see the point on
  ``Power and Heating''.

  Note that there are several kinds of transfers going on here, and that
  these are quoted in different units. First of all there is the
  platter-to-drive cache transfer, usually quoted in Mbits/s. Typical
  values here is about 50-250 Mbits/s. The second stage is from the
  built in drive cache to the adapter, and this is typically quoted in
  MB/s, and typical quoted values here is 3-40 MB/s. Note, however, that
  this assumed data is already in the cache and hence for maximum
  readout speed from the drive the effective transfer rate will decrease
  dramatically.

  3.3.2.  Optical drives

  Optical read/write drives exist but are slow and not so common. They
  were used in the NeXT machine but the low speed was a source for much
  of the complaints. The low speed is mainly due to the thermal nature
  of the phase change that represents the data storage. Even when using
  relatively powerful lasers to induce the phase changes the effects are
  still slower than the magnetic effect used in magnetic drives.

  Today many people use CD-ROM drives which, as the name suggests, is
  read-only. Storage is about 650MB, transfer speeds are variable,
  depending on the drive but can exceed 1.5MB/s. Data is stored on a
  spiraling single track so it is not useful to talk about geometry for
  this. Data density is constant so the drive uses constant linear
  velocity (CLV). Seek is also slower, about 100ms, partially due to the
  spiraling track. Recent, high speed drives, use a mix of CLV and CAV
  in order to maximize performance. This also reduces access time caused
  by the need to reach correct rotational speed for readout.

  A new type (DVD) is on the horizon, offering up to about 18GB on a
  single disk.

  3.3.3.  Solid State Drives

  This is a relatively recent addition to the available technology and
  has been made popular especially in portable computers as well as in
  embedded systems. Containing no movable parts they are very fast both
  in terms of access and transfer rates. The most popular type is flash
  RAM, but also other types of RAM is used. A few years ago many had
  great hopes for magnetic bubble memories but it turned out to be
  relatively expensive and is not that common.

  In general the use of RAM disks are regarded as a bad idea as it is
  normally more sensible to add more RAM to the motherboard and let the
  operating system divide the memory pool into buffers, cache, program
  and data areas. Only in very special cases, such as real time systems
  with short time margins, can RAM disks be a sensible solution.

  Flash RAM is today available in several 10's of megabytes in storage
  and one might be tempted to use it for fast, temporary storage in a
  computer. There is however a huge snag with this: flash RAM has a
  finite life time in terms of the number of times you can rewrite data,
  so putting swap, /tmp or /var/tmp on such a device will certainly
  shorten its lifetime dramatically.  Instead, using flash RAM for
  directories that are read often but rarely written to, will be a big
  performance win.

  In order to get the optimum life time out of flash RAM you will need
  to use special drivers that will use the RAM evenly and minimize the
  number of block erases.

  This example illustrates the advantages of splitting up your directory
  structure over several devices.

  Solid state drives have no real cylinder/head/sector addressing but
  for compatibility reasons this is simulated by the driver to give a
  uniform interface to the operating system.

  3.4.  Interfaces

  There is a plethora of interfaces to chose from widely ranging in
  price and performance. Most motherboards today include IDE interface
  or better, Intel supports it through the Triton PCI chip set which is
  very popular these days. Many motherboards also include a SCSI
  interface chip made by NCR and that is connected directly to the PCI
  bus.  Check what you have and what BIOS support you have with it.

  3.4.1.  MFM and RLL

  Once upon a time this was the established technology, a time when 20MB
  was awesome, which compared to todays sizes makes you think that
  dinosaurs roamed the Earth with these drives. Like the dinosaurs these
  are outdated and are slow and unreliable compared to what we have
  today. Linux does support this but you are well advised to think twice
  about what you would put on this. One might argue that an emergency
  partition with a suitable vintage of DOS might be fitting.

  3.4.2.  ESDI

  Actually, ESDI was an adaptation of the very widely used SMD interface
  used on "big" computers to the cable set used with the ST506
  interface, which was more convenient to package than the 60-pin +
  26-pin connector pair used with SMD.  The ST506 was a "dumb" interface
  which relied entirely on the controller and host computer to do
  everything from computing head/cylinder/sector locations and keeping
  track of the head location, etc. ST506 required the controller to
  extract clock from the recovered data, and control the physical
  location of detailed track features on the medium, bit by bit. It had
  about a 10-year life if you include the use of MFM, RLL, and ERLL/ARLL
  modulation schemes. ESDI, on the other hand, had intelligence, often
  using three or four separate microprocessors on a single drive, and
  high-level commands to format a track, transfer data, perform seeks,
  and so on. Clock recovery from the data stream was accomplished at the
  drive, which drove the clock line and presented its data in NRZ,
  though error correction was still the task of the controller.  ESDI
  allowed the use of variable bit density recording, or, for that
  matter, any other modulation technique, since it was locally generated
  and resolved at the drive. Though many of the techniques used in ESDI
  were later incorporated in IDE, it was the increased popularity of
  SCSI which led to the demise of ESDI in computers. ESDI had a life of
  about 10 years, though mostly in servers and otherwise "big" systems
  rather than PC's.

  3.4.3.  IDE and ATA

  Progress made the drive electronics migrate from the ISA slot card
  over to the drive itself and Integrated Drive Electronics was borne.
  It was simple, cheap and reasonably fast so the BIOS designers
  provided the kind of snag that the computer industry is so full of. A
  combination of an IDE limitation of 16 heads together with the BIOS
  limitation of 1024 cylinders gave us the infamous 504MB limit.
  Following the computer industry traditions again, the snag was patched
  with a kludge and we got all sorts of translation schemes and BIOS
  bodges. This means that you need to read the installation
  documentation very carefully and check up on what BIOS you have and
  what date it has as the BIOS has to tell Linux what size drive you
  have. Fortunately with Linux you can also tell the kernel directly
  what size drive you have with the drive parameters, check the
  documentation for LILO and Loadlin, thoroughly. Note also that IDE is
  equivalent to ATA, AT Attachment.  IDE uses CPU-intensive Programmed
  Input/Output (PIO) to transfer data to and from the drives and has no
  capability for the more efficient Direct Memory Access (DMA)
  technology. Highest transfer rate is 8.3MB/s.

  3.4.4.  EIDE, Fast-ATA and ATA-2

  These 3 terms are roughly equivalent, fast-ATA is ATA-2 but EIDE
  additionally includes ATAPI. ATA-2 is what most use these days which
  is faster and with DMA. Highest transfer rate is increased to 16.6
  MB/s.

  3.4.5.  Ultra-ATA

  A new, faster DMA mode that is approximately twice the speed of EIDE
  PIO-Mode 4 (33 MB/s). Disks with and without Ultra-ATA can be mixed on
  the same cable without speed penalty for the faster adapters. The
  Ultra-ATA interface is electrically identical with the normal Fast-ATA
  interface, including the maximum cable length.

  3.4.6.  ATAPI

  The ATA Packet Interface was designed to support CD-ROM drives using
  the IDE port and like IDE it is cheap and simple.

  3.4.7.  SCSI

  The Small Computer System Interface is a multi purpose interface that
  can be used to connect to everything from drives, disk arrays,
  printers, scanners and more. The name is a bit of a misnomer as it has
  traditionally been used by the higher end of the market as well as in
  work stations since it is well suited for multi tasking environments.

  The standard interface is 8 bits wide and can address 8 devices.
  There is a wide version with 16 bit that is twice as fast on the same
  clock and can address 16 devices. The host adapter always counts as a
  device and is usually number 7.  It is also possible to have 32 bit
  wide busses but this usually requires a double set of cables to carry
  all the lines.

  The old standard was 5MB/s and the newer fast-SCSI increased this to
  10MB/s. Recently ultra-SCSI, also known as Fast-20, arrived with 20
  MB/s transfer rates for an 8 bit wide bus.

  The higher performance comes at a cost that is usually higher than for
  (E)IDE. The importance of correct termination and good quality cables
  cannot be overemphasized. SCSI drives also often tend to be of a
  higher quality than IDE drives. Also adding SCSI devices tend to be
  easier than adding more IDE drives: Often it is only a matter of
  plugging or unplugging the device; some people do this without
  powering down the system. This feature is most convenient when you
  have multiple systems and you can just take the devices from one
  system to the other should one of them fail for some reason.

  There is a number of useful documents you should read if you use SCSI,
  the SCSI HOWTO as well as the SCSI FAQ posted on Usenet News.

  SCSI also has the advantage you can connect it easily to tape drives
  for backing up your data, as well as some printers and scanners. It is
  even possible to use it as a very fast network between computers while
  simultaneously share SCSI devices on the same bus. Work is under way
  but due to problems with ensuring cache coherency between the
  different computers connected, this is a non trivial task.

  3.5.  Cabling

  I do not intend to make too many comments on hardware but I feel I
  should make a little note on cabling. This might seem like a
  remarkably low technological piece of equipment, yet sadly it is the
  source of many frustrating problems. At todays high speeds one should
  think of the cable more of a an RF device with its inherent demands on
  impedance matching. If you do not take your precautions you will get a
  much reduced reliability or total failure. Some SCSI host adapters are
  more sensitive to this than others.

  Shielded cables are of course better than unshielded but the price is
  much higher. With a little care you can get good performance from a
  cheap unshielded cable.

  ╖  For Fast-ATA and Ultra-ATA, the maximum cable length is specified
     as 45cm (18"). The data lines of both IDE channels are connected on
     many boards, though, so they count as one cable. In any case EIDE
     cables should be as short as possible. If there are mysterious
     crashes or spontaneous changes of data, it is well worth
     investigating your cabling.  Try a lower PIO mode or disconnect the
     second channel and see if the problem still occurs.

  ╖  Use as short cable as possible, but do not forget the 30cm minimum
     separation for ultra SCSI.

  ╖  Avoid long stubs between the cable and the drive, connect the plug
     on the cable directly to the drive without an extension.

  ╖  Use correct termination for SCSI devices and at the correct
     position: the end of the SCSI chain.

  ╖  Do not mix shielded or unshielded cabling, do not wrap cables
     around metal, try to avoid proximity to metal parts along parts of
     the cabling. Any such discontinuities can cause impedance
     mismatching which in turn can cause reflection of signals which
     increases noise on the cable.  This problems gets even more severe
     in the case of multi channel controllers.  Recently someone
     suggested wrapping bubble plastic around the cables in order to
     avoid too close proximity to metal, a real problem inside crowded
     cabinets.

  3.6.  Host Adapters

  This is the other end of the interface from the drive, the part that
  is connected to a computer bus. The speed of the computer bus and that
  of the drives should be roughly similar, otherwise you have a
  bottleneck in your system. Connecting a RAID 0 disk-farm to a ISA card
  is pointless. These days most computers come with 32 bit PCI bus
  capable of 132MB/s transfers which should not represent a bottleneck
  for most people in the near future.

  As the drive electronic migrated to the drives the remaining part that
  became the (E)IDE interface is so small it can easily fit into the PCI
  chip set. The SCSI host adapter is more complex and often includes a
  small CPU of its own and is therefore more expensive and not
  integrated into the PCI chip sets available today. Technological
  evolution might change this.

  Some host adapters come with separate caching and intelligence but as
  this is basically second guessing the operating system the gains are
  heavily dependent on which operating system is used. Some of the more
  primitive ones, that shall remain nameless, experience great gains.
  Linux, on the other hand, have so much smarts of its own that the
  gains are much smaller.

  Mike Neuffer, who did the drivers for the DPT controllers, states that
  the DPT controllers are intelligent enough that given enough cache
  memory it will give you a big push in performance and suggests that
  people who have experienced little gains with smart controllers just
  have not used a sufficiently intelligent caching controller.

  3.7.  Multi Channel Systems

  In order to increase throughput it is necessary to identify the most
  significant bottlenecks and then eliminate them. In some systems, in
  particular where there are a great number of drives connected, it is
  advantageous to use several controllers working in parallel, both for
  SCSI host adapters as well as IDE controllers which usually have 2
  channels built in. Linux supports this.

  Some RAID controllers feature 2 or 3 channels and it pays to spread
  the disk load across all channels. In other words, if you have two
  SCSI drives you want to RAID and a two channel controller, you should
  put each drive on separate channels.

  3.8.  Multi Board Systems

  In addition to having both a SCSI and an IDE in the same machine it is
  also possible to have more than one SCSI controller. Check the SCSI-
  HOWTO on what controllers you can combine. Also you will most likely
  have to tell the kernel it should probe for more than just a single
  SCSI or a single IDE controller. This is done using kernel parameters
  when booting, for instance using LILO.  Check the HOWTOs for SCSI and
  LILO for how to do this.

  3.9.  Speed Comparison

  The following tables are given just to indicate what speeds are
  possible but remember that these are the theoretical maximum speeds.
  All transfer rates are in MB per second and bus widths are measured in
  bits.

  3.9.1.  Controllers

       IDE             :       8.3 - 16.7
       Ultra-ATA       :       33

       SCSI            :
                               Bus width (bits)

       Bus Speed (MHz)         |        8      16      32
       --------------------------------------------------
        5                      |        5      10      20
       10  (fast)              |       10      20      40
       20  (fast-20 / ultra)   |       20      40      80
       40  (fast-40 / ultra-2) |       40      80      --
       --------------------------------------------------

  3.9.2.  Bus types

       ISA             :       8-12
       EISA            :       33
       VESA            :       40    (Sometimes tuned to 50)

       PCI
                               Bus width (bits)

       Bus Speed (MHz)         |       32      64
       --------------------------------------------------
       33                      |       132     264
       66                      |       264     528
       --------------------------------------------------

  3.10.  Benchmarking

  This is a very, very difficult topic and I will only make a few
  cautious comments about this minefield. First of all, it is more
  difficult to make comparable benchmarks that have any actual meaning.
  This, however, does not stop people from trying...

  Instead one can use benchmarking to diagnose your own system, to check
  it is going as fast as it should, that is, not slowing down.  Also you
  would expect a significant increase when switching from a simple file
  system to RAID, so a lack of performance gain will tell you something
  is wrong.
  When you try to benchmark you should not hack up your own, instead
  look up iozone and bonnie and read the documentation very carefully.
  More information about this is coming soon.

  3.11.  Comparisons

  SCSI offers more performance than EIDE but at a price.  Termination is
  more complex but expansion not too difficult.  Having more than 4 (or
  in some cases 2) IDE drives can be complicated, with wide SCSI you can
  have up to 15 per adapter.  Some SCSI host adapters have several
  channels thereby multiplying the number of possible drives even
  further.

  RLL and MFM is in general too old, slow and unreliable to be of much
  use.

  3.12.  Future Development

  SCSI-3 is under way and will hopefully be released soon. Faster
  devices are already being announced, most recently an 80MB/s monster
  specification has been proposed.  This is based around the ultra-2
  standard (which used a 40MHz clock) combined with a 16 bit cable.

  Some manufacturers already announce SCSI-3 devices but this is
  currently rather premature as the standard is not yet firm. As the
  transfer speeds increase the saturation point of the PCI bus is
  getting closer. Currently the 64 bit version has a limit of 264MB/s.
  The PCI transfer rate will in the future be increased from the current
  33MHz to 66MHz, thereby increasing the limit to 528MB/s.

  Another trend is for larger and larger drives. I hear it is possible
  to get 55GB on a single drive though this is rather expensive.
  Currently the optimum storage for your money is about 5GB but also
  this is continuously increasing. The introduction of DVD will in the
  near future have a big impact, with nearly 20GB on a single disk you
  can have a complete copy of even major FTP sites from around the
  world. The only thing we can be reasonably sure about the future is
  that even if it won't get any better, it will definitely be bigger.

  Addendum: soon after I first wrote this I read that the maximum useful
  speed for a CD-ROM was 20x as mechanical stability would be too great
  a problem at these speeds. About one month after that again the first
  commercial 24x CD-ROMs were available...

  3.13.  Recommendations

  My personal view is that EIDE is the best way to start out on your
  system, especially if you intend to use DOS as well on your machine.
  If you plan to expand your system over many years or use it as a
  server I would strongly recommend you get SCSI drives. Currently wide
  SCSI is a little more expensive. You are generally more likely to get
  more for your money with standard width SCSI. There is also
  differential versions of the SCSI bus which increases maximum length
  of the cable. The price increase is even more substantial and cannot
  therefore be recommended for normal users.

  In addition to disk drives you can also connect some types of scanners
  and printers and even networks to a SCSI bus.

  Also keep in mind that as you expand your system you will draw ever
  more power, so make sure your power supply is rated for the job and
  that you have sufficient cooling. Many SCSI drives offer the option of
  sequential spin-up which is a good idea for large systems.  See also
  the point on ``Power and Heating''.

  4.  Considerations

  The starting point in this will be to consider where you are and what
  you want to do. The typical home system starts out with existing
  hardware and the newly converted Linux user will want to get the most
  out of existing hardware. Someone setting up a new system for a
  specific purpose (such as an Internet provider) will instead have to
  consider what the goal is and buy accordingly. Being ambitious I will
  try to cover the entire range.

  Various purposes will also have different requirements regarding file
  system placement on the drives, a large multiuser machine would
  probably be best off with the /home directory on a separate disk, just
  to give an example.

  In general, for performance it is advantageous to split most things
  over as many disks as possible but there is a limited number of
  devices that can live on a SCSI bus and cost is naturally also a
  factor. Equally important, file system maintenance becomes more
  complicated as the number of partitions and physical drives increases.

  4.1.  File system features

  The various parts of FSSTND have different requirements regarding
  speed, reliability and size, for instance losing root is a pain but
  can easily be recovered. Losing /var/spool/mail is a rather different
  issue. Here is a quick summary of some essential parts and their
  properties and requirements. Note that this is just a guide, there can
  be binaries in etc and lib directories, libraries in bin directories
  and so on.

  4.1.1.  Swap

     Speed
        Maximum! Though if you rely too much on swap you should consider
        buying some more RAM. Note, however, that on many PC
        motherboards the cache will not work on RAM above 128MB.

     Size
        Similar as for RAM. Quick and dirty algorithm: just as for tea:
        16MB for the machine and 2MB for each user. Smallest kernel run
        in 1MB but is tight, use 4MB for general work and light
        applications, 8MB for X11 or GCC or 16MB to be comfortable.
        (The author is known to brew a rather powerful cuppa tea...)

        Some suggest that swap space should be 1-2 times the size of the
        RAM, pointing out that the locality of the programs determines
        how effective your added swap space is. Note that using the same
        algorithm as for 4BSD is slightly incorrect as Linux does not
        allocate space for pages in core.

        Also remember to take into account the type of programs you use.
        Some programs that have large working sets, such as finite
        element modeling (FEM) have huge data structures loaded in RAM
        rather than working explicitly on disk files. Data and computing
        intensive programs like this will cause excessive swapping if
        you have less RAM than the requirements.

        Other types of programs can lock their pages into RAM. This can
        be for security reasons, preventing copies of data reaching a
        swap device or for performance reasons such as in a real time
        module. Either way, locking pages reduces the remaining amount
        of swappable memory and can cause the system to swap earlier
        then otherwise expected.

        In man 8 mkswap it is explained that each swap partition can be
        a maximum of just under 128 MB in size.

     Reliability
        Medium. When it fails you know it pretty quickly and failure
        will cost you some lost work. You save often, don't you?

     Note 1
        Linux offers the possibility of interleaved swapping across
        multiple devices, a feature that can gain you much. Check out
        "man 8 swapon" for more details. However, software raiding swap
        across multiple devices adds more overheads than you gain.

        Thus the /etc/fstab file might look like this:

          /dev/sda1       swap            swap    pri=1           0       0
          /dev/sdc1       swap            swap    pri=1           0       0

     Remember that the fstab file is very sensitive to the formatting
     used, read the man page carefully and do not just cut and paste the
     lines above.

     Note 2
        Some people use a RAM disk for swapping or some other file
        systems. However, unless you have some very unusual requirements
        or setups you are unlikely to gain much from this as this cuts
        into the memory available for caching and buffering.

  4.1.2.  Temporary storage (/tmp and /var/tmp)

     Speed
        Very high. On a separate disk/partition this will reduce
        fragmentation generally, though ext2fs handles fragmentation
        rather well.

     Size
        Hard to tell, small systems are easy to run with just a few MB
        but these are notorious hiding places for stashing files away
        from prying eyes and quota enforcements and can grow without
        control on larger machines. Suggested: small home machine: 8MB,
        large home machine: 32MB, small server: 128MB, and large
        machines up to 500MB (The machine used by the author at work has
        1100 users and a 300MB /tmp directory). Keep an eye on these
        directories, not only for hidden files but also for old files.
        Also be prepared that these partitions might be the first reason
        you might have to resize your partitions.

     Reliability
        Low. Often programs will warn or fail gracefully when these
        areas fail or are filled up. Random file errors will of course
        be more serious, no matter what file area this is.

     Files
        Mostly short files but there can be a huge number of them.
        Normally programs delete their old tmp files but if somehow an
        interruption occurs they could survive. Many distributions have
        a policy regarding cleaning out tmp files at boot time, you
        might want to check out what your setup is.

     Note
        In FSSTND there is a note about putting /tmp on RAM disk. This,
        however, is not recommended for the same reasons as stated for
        swap. Also, as noted earlier, do not use flash RAM drives for
        these directories. One should also keep in mind that some
        systems are set to automatically clean tmp areas on rebooting.

  (* That was 50 lines, I am home and dry! *)

  4.1.3.  Spool areas (/var/spool/news and /var/spool/mail)

     Speed
        High, especially on large news servers. News transfer and
        expiring are disk intensive and will benefit from fast drives.
        Print spools: low. Consider RAID0 for news.

     Size
        For news/mail servers: whatever you can afford. For single user
        systems a few MB will be sufficient if you read continuously.
        Joining a list server and taking a holiday is, on the other
        hand, not a good idea.  (Again the machine I use at work has
        100MB reserved for the entire /var/spool)

     Reliability
        Mail: very high, news: medium, print spool: low. If your mail is
        very important (isn't it always?) consider RAID for reliability.

     Files
        Usually a huge number of files that are around a few KB in size.
        Files in the print spool can on the other hand be few but quite
        sizable.

     Note
        Some of the news documentation suggests putting all the
        .overview files on a drive separate from the news files, check
        out all news FAQs for more information.

  4.1.4.  Home directories (/home)

     Speed
        Medium. Although many programs use /tmp for temporary storage,
        others such as some news readers frequently update files in the
        home directory which can be noticeable on large multiuser
        systems. For small systems this is not a critical issue.

     Size
        Tricky! On some systems people pay for storage so this is
        usually then a question of finance. Large systems such as
        nyx.net <http://www.nyx.net/> (which is a free Internet service
        with mail, news and WWW services) run successfully with a
        suggested limit of 100K per user and 300K as enforced maximum.
        Commercial ISPs offer typically about 5MB in their standard
        subscription packages.

        If however you are writing books or are doing design work the
        requirements balloon quickly.

     Reliability
        Variable. Losing /home on a single user machine is annoying but
        when 2000 users call you to tell you their home directories are
        gone it is more than just annoying. For some their livelihood
        relies on what is here. You do regular backups of course?

     Files
        Equally tricky. The minimum setup for a single user tends to be
        a dozen files, 0.5 - 5 kB in size. Project related files can be
        huge though.

     Note1
        You might consider RAID for either speed or reliability. If you
        want extremely high speed and reliability you might be looking
        at other operating system and hardware platforms anyway.  (Fault
        tolerance etc.)

     Note2
        Web browsers often use a local cache to speed up browsing and
        this cache can take up a substantial amount of space and cause
        much disk activity. There are many ways of avoiding this kind of
        performance hits, for more information see the sections on
        ``Home Directories'' and ``WWW''.

     Note3
        Users often tend to use up all available space on the /home
        partition. The Linux Quota subsystem is capable of limiting the
        number of blocks and the number of inode a single user ID can
        allocate on a per-filesystem basis. See the Linux Quota mini-
        HOWTO <http://sunsite.unc.edu/LDP/mini> by Albert M.C. Tam
        <mailto:bertie (at) scn.org> for details on setup.

  4.1.5.  Main binaries ( /usr/bin and /usr/local/bin)

     Speed
        Low. Often data is bigger than the programs which are demand
        loaded anyway so this is not speed critical. Witness the
        successes of live file systems on CD ROM.

     Size
        The sky is the limit but 200MB should give you most of what you
        want for a comprehensive system. A big system, for software
        development or a multi purpose server should perhaps reserve
        500MB both for installation and for growth.

     Reliability
        Low. This is usually mounted under root where all the essentials
        are collected. Nevertheless losing all the binaries is a pain...

     Files
        Variable but usually of the order of 10 - 100 kB.

  4.1.6.  Libraries ( /usr/lib and /usr/local/lib)

     Speed
        Medium. These are large chunks of data loaded often, ranging
        from object files to fonts, all susceptible to bloating. Often
        these are also loaded in their entirety and speed is of some use
        here.

     Size
        Variable. This is for instance where word processors store their
        immense font files. The few that have given me feedback on this
        report about 70MB in their various lib directories.  A rather
        complete Debian 1.2 installation can take as much as 250MB which
        can be taken as an realistic upper limit.  The following ones
        are some of the largest disk space consumers: GCC, Emacs,
        TeX/LaTeX, X11 and perl.

     Reliability
        Low. See point ``Main binaries''.

     Files
        Usually large with many of the order of 100 kB in size.

     Note
        For historical reasons some programs keep executables in the lib
        areas. One example is GCC which have some huge binaries in the
        /usr/lib/gcc/lib hierarchy.

  4.1.7.  Root

     Speed
        Quite low: only the bare minimum is here, much of which is only
        run at startup time.

     Size
        Relatively small. However it is a good idea to keep some
        essential rescue files and utilities on the root partition and
        some keep several kernel versions. Feedback suggests about 20MB
        would be sufficient.

     Reliability
        High. A failure here will possibly cause a fair bit of grief and
        you might end up spending some time rescuing your boot
        partition. With some practice you can of course do this in an
        hour or so, but I would think if you have some practice doing
        this you are also doing something wrong.

        Naturally you do have a rescue disk? Of course this is updated
        since you did your initial installation? There are many ready
        made rescue disks as well as rescue disk creation tools you
        might find valuable.  Presumably investing some time in this
        saves you from becoming a root rescue expert.

     Note 1
        If you have plenty of drives you might consider putting a spare
        emergency boot partition on a separate physical drive. It will
        cost you a little bit of space but if your setup is huge the
        time saved, should something fail, will be well worth the extra
        space.

     Note 2
        For simplicity and also in case of emergencies it is not
        advisable to put the root partition on a RAID level 0 system.
        Also if you use RAID for your boot partition you have to
        remember to have the md option turned on for your emergency
        kernel.

  4.1.8.  DOS etc.

  At the danger of sounding heretical I have included this little
  section about something many reading this document have strong
  feelings about.  Unfortunately many hardware items come with setup and
  maintenance tools based around those systems, so here goes.

     Speed
        Very low. The systems in question are not famed for speed so
        there is little point in using prime quality drives.
        Multitasking or multi-threading are not available so the command
        queueing facility found in SCSI drives will not be taken
        advantage of. If you have an old IDE drive it should be good
        enough. The exception is to some degree Win95 and more notably
        NT which have multi-threading support which should theoretically
        be able to take advantage of the more advanced features offered
        by SCSI devices.

     Size
        The company behind these operating systems is not famed for
        writing tight code so you have to be prepared to spend a few
        tens of MB depending on what version you install of the OS or
        Windows. With an old version of DOS or Windows you might fit it
        all in on 50MB.

     Reliability
        Ha-ha. As the chain is no stronger than the weakest link you can
        use any old drive. Since the OS is more likely to scramble
        itself than the drive is likely to self destruct you will soon
        learn the importance of keeping backups here.

        Put another way: "Your mission, should you choose to accept it,
        is to keep this partition working. The warranty will self
        destruct in 10 seconds..."

        Recently I was asked to justify my claims here. First of all I
        am not calling DOS and Windows sorry excuses for operating
        systems. Secondly there are various legal issues to be taken
        into account. Saying there is a connection between the last two
        sentences are merely the ravings of the paranoid. Surely.
        Instead I shall offer the esteemed reader a few key words: DOS
        4.0, DOS 6.x and various drive compression tools that shall
        remain nameless.

  4.2.  Explanation of terms

  Naturally the faster the better but often the happy installer of Linux
  has several disks of varying speed and reliability so even though this
  document describes performance as 'fast' and 'slow' it is just a rough
  guide since no finer granularity is feasible. Even so there are a few
  details that should be kept in mind:

  4.2.1.  Speed

  This is really a rather woolly mix of several terms: CPU load,
  transfer setup overhead, disk seek time and transfer rate. It is in
  the very nature of tuning that there is no fixed optimum, and in most
  cases price is the dictating factor. CPU load is only significant for
  IDE systems where the CPU does the transfer itself but is generally
  low for SCSI, see SCSI documentation for actual numbers. Disk seek
  time is also small, usually in the millisecond range. This however is
  not a problem if you use command queueing on SCSI where you then
  overlap commands keeping the bus busy all the time. News spools are a
  special case consisting of a huge number of normally small files so in
  this case seek time can become more significant.

  There are two main parameters that are of interest here:

     Seek
        is usually specified in the average time take for the read/write
        head to seek from one track to another. This parameter is
        important when dealing with a large number of small files such
        as found in spool files.  There is also the extra seek delay
        before the desired sector rotates into position under the head.
        This delay is dependent on the angular velocity of the drive
        which is why this parameter quite often is quoted for a drive.
        Common values are 4500, 5400 and 7200 rpm (rotations per
        minute). Higher rpm reduces the seek time but at a substantial
        cost.  Also drives working at 7200 rpm have been known to be
        noisy and to generate a lot of heat, a factor that should be
        kept in mind if you are building a large array or "disk farm".
        Very recently drives working at 10000 rpm has entered the market
        and here the cooling requirements are even stricter and minimum
        figures for air flow are given.

     Transfer
        is usually specified in megabytes per second.  This parameter is
        important when handling large files that have to be transferred.
        Library files, dictionaries and image files are examples of
        this. Drives featuring a high rotation speed also normally have
        fast transfers as transfer speed is proportional to angular
        velocity for the same sector density.

  It is therefore important to read the specifications for the drives
  very carefully, and note that the maximum transfer speed quite often
  is quoted for transfers out of the on board cache (burst speed) and
  not directly from the platter (sustained speed).  See also section on
  ``Power and Heating''.

  4.2.2.  Reliability

  Naturally no-one would want low reliability disks but one might be
  better off regarding old disks as unreliable. Also for RAID purposes
  (See the relevant information) it is suggested to use a mixed set of
  disks so that simultaneous disk crashes become less likely.

  So far I have had only one report of total file system failure but
  here unstable hardware seemed to be the cause of the problems.

  4.2.3.  Files

  The average file size is important in order to decide the most
  suitable drive parameters. A large number of small files makes the
  average seek time important whereas for big files the transfer speed
  is more important.  The command queueing in SCSI devices is very handy
  for handling large numbers of small files, but for transfer EIDE is
  not too far behind SCSI and normally much cheaper than SCSI.

  4.3.  Technologies

  In order to decide how to get the most of your devices you need to
  know what technologies are available and their implications. As always
  there can be some tradeoffs with respect to speed, reliability, power,
  flexibility, ease of use and complexity.

  4.3.1.  RAID

  This is a method of increasing reliability, speed or both by using
  multiple disks in parallel thereby decreasing access time and
  increasing transfer speed. A checksum or mirroring system can be used
  to increase reliability.  Large servers can take advantage of such a
  setup but it might be overkill for a single user system unless you
  already have a large number of disks available. See other documents
  and FAQs for more information.

  For Linux one can set up a RAID system using either software (the md
  module in the kernel), a Linux compatible controller card (PCI-to-
  SCSI) or a SCSI-to-SCSI controller. Check the documentation for what
  controllers can be used. A hardware solution is usually faster, and
  perhaps also safer, but comes at a significant cost.

  SCSI-to-SCSI controllers are usually implemented as complete cabinets
  with drives and a controller that connects to the computer with a
  second SCSI bus. This makes the entire cabinet of drives look like a
  single large, fast SCSI drive and requires no special RAID driver. The
  disadvantage is that the SCSI bus connecting the cabinet to the
  computer becomes a bottleneck.

  PCI-to-SCSI are as the name suggests, connected to the high speed PCI
  bus and is therefore not suffering from the same bottleneck as the
  SCSI-to-SCSI controllers. These controllers require special drivers
  but you also get the means of controlling the RAID configuration over
  the network which simplifies management.

  Currently the only supported SCSI RAID controller cards are the
  SmartCache I/III/IV and SmartRAID I/III/IV controller families from
  DPT. These controllers are supported by the EATA-DMA driver in the
  standard kernel. This company also has an informative home page
  <http://www.dpt.com> which also describes various general aspects of
  RAID and SCSI in addition to the product related information.

  More information from  the author of the DPT controller drivers (EATA*
  drivers) can be found at his pages on SCSI <http://www.uni-
  mainz.de/~neuffer/scsi> and DPT <http://www.uni-
  mainz.de/~neuffer/scsi/dpt>.

  SCSI-to-SCSI-controllers are small computers themselves, often with a
  substantial amount of cache RAM. To the host system they mask
  themselves as a gigantic, fast and reliable SCSI disk whereas to their
  disks they look like the computer's SCSI host adapter. Some of these
  controllers have the option to talk to multiple hosts simultaneously.
  Since these controllers look to the host as a normal, albeit large
  SCSI drive they need no special support from the host system. Usually
  they are configured via the front panel or with a vt100 terminal
  emulator connected to their on-board serial interface.

  Very recently I have heard that Syred also makes SCSI-to-SCSI
  controllers that are supported under Linux. I have no more information
  about this yet but will come back with more information soon. In the
  mean time check out their home <http://www.syred.com> pages for more
  information.

  RAID comes in many levels and flavours which I will give a brief
  overview of this here. Much has been written about it and the
  interested reader is recommended to read more about this in the RAID
  FAQ.

  ╖  RAID 0 is not redundant at all but offers the best throughput of
     all levels here. Data is striped across a number of drives so read
     and write operations take place in parallel across all drives. On
     the other hand if a single drive fail then everything is lost. Did
     I mention backups?

  ╖  RAID 1 is the most primitive method of obtaining redundancy by
     duplicating data across all drives. Naturally this is massively
     wasteful but you get one substantial advantage which is fast
     access.  The drive that access the data first wins. Transfers are
     not any faster than for a single drive, even though you might get
     some faster read transfers by using one track reading per drive.

     Also if you have only 2 drives this is the only method of achieving
     redundancy.

  ╖  RAID 2 and 4 are not so common and are not covered here.

  ╖  RAID 3 uses a number of disks (at least 2) to store data in a
     striped RAID 0 fashion. It also uses an additional redundancy disk
     to store the XOR sum of the data from the data disks. Should the
     redundancy disk fail, the system can continue to operate as if
     nothing happened. Should any single data disk fail the system can
     compute the data on this disk from the information on the
     redundancy disk and all remaining disks. Any double fault will
     bring the whole RAID set off-line.

     RAID 3 makes sense only with at least 2 data disks (3 disks
     including the redundancy disk). Theoretically there is no limit for
     the number of disks in the set, but the probability of a fault
     increases with the number of disks in the RAID set. Usually the
     upper limit is 5 to 7 disks in a single RAID set.

     Since RAID 3 stores all redundancy information on a dedicated disk
     and since this information has to be updated whenever a write to
     any data disk occurs, the overall write speed of a RAID 3 set is
     limited by the write speed of the redundancy disk. This, too, is a
     limit for the number of disks in a RAID set. The overall read speed
     of a RAID 3 set with all data disks up and running is that of a
     RAID 0 set with that number of data disks. If the set has to
     reconstruct data stored on a failed disk from redundant
     information, the performance will be severely limited: All disks in
     the set have to be read and XOR-ed to compute the missing
     information.

  ╖  RAID 5 is just like RAID 3, but the redundancy information is
     spread on all disks of the RAID set. This improves write
     performance, because load is distributed more evenly between all
     available disks.

  There are also hybrids available based on RAID 1 and one other level.
  Many combinations are possible but I have only seen a few referred to.
  These are more complex than the above mentioned RAID levels.

  RAID 0/1 combines striping with duplication which gives very high
  transfers combined with fast seeks as well as redundancy. The
  disadvantage is high disk consumption as well as the above mentioned
  complexity.

  RAID 1/5 combines the speed and redundancy benefits of RAID5 with the
  fast seek of RAID1. Redundancy is improved compared to RAID 0/1 but
  disk consumption is still substantial. Implementing such a system
  would involve typically more than 6 drives, perhaps even several
  controllers or SCSI channels.

  4.3.2.  AFS, Veritas and Other Volume Management Systems

  Although multiple partitions and disks have the advantage of making
  for more space and higher speed and reliability there is a significant
  snag: if for instance the /tmp partition is full you are in trouble
  even if the news spool is empty, as it is not easy to retransfer
  quotas across partitions. Volume management is a system that does just
  this and AFS and Veritas are two of the best known examples. Some also
  offer other file systems like log file systems and others optimised
  for reliability or speed. Note that Veritas is not available (yet) for
  Linux and it is not certain they can sell kernel modules without
  providing source for their proprietary code, this is just mentioned
  for information on what is out there. Still, you can check their home
  page <http://www.veritas.com> to see how such systems function.

  Derek Atkins, of MIT, ported AFS to Linux and has also set up the
  Linux AFS mailing List for this which is open to the public.  Requests
  to join the list should go to Request and finally bug reports should
  be directed to Bug Reports.

  Important: as AFS uses encryption it is restricted software and cannot
  easily be exported from the US. AFS is now sold by Transarc and they
  have set up a www site. The directory structure there has been
  reorganized recently so I cannot give a more accurate URL than just
  the Transarc Home Page <http://www.transarc.com> which lands you in
  the root of the web site. There you can also find much general
  information as well as a FAQ.

  The is now also development based on the last free sources of AFS.

  Volume management is for the time being an area where Linux is
  lacking.  Someone has recently started a virtual partition system
  project that will reimplement many of the volume management functions
  found in IBM's AIX system.

  4.3.3.  Linux md Kernel Patch

  There is however one kernel project that attempts to do some of this,
  md, which has been part of the kernel distributions since 1.3.69.
  Currently providing spanning and RAID it is still in early development
  and people are reporting varying degrees of success as well as total
  wipe out. Use with caution.

  Currently it offers linear mode and RAID levels 0,1,4,5; all in
  various stages of development and reliability with linear mode and
  RAID levels 0 and 1 being the most stable.  It is also possible to
  stack some levels, for instance mirroring (RAID 1) two pairs of
  drives, each pair set up as striped disks (RAID 0), which offers the
  speed of RAID 0 combined with the reliability of RAID 1.

  Think very carefully what drives you combine so you can operate all
  drives in parallel, which gives you better performance and less wear.
  Read more about this in the documentation that comes with md.

  4.3.4.  General File System Consideration

  In the Linux world ext2fs is well established as a general purpose
  system.  Still for some purposes others can be a better choice. News
  spools lend themselves to a log file based system whereas high
  reliability data might need other formats. This is a hotly debated
  topic and there are currently few choices available but work is
  underway. Log file systems also have the advantage of very fast file
  checking. Mail servers in the 100GB class can suffer file checks
  taking several days before becoming operational after rebooting.

  The Minix file system is the oldest one, used in some rescue disk
  systems but otherwise very little used these days. At one time the
  Xiafs was a strong contender to the standard for Linux but seems to
  have fallen behind these days.

  Adam Richter from Yggdrasil posted recently that they have been
  working on a compressed log file based system but that this project is
  currently on hold. Nevertheless a non-working version is available on
  their FTP server. Check out the Yggdrasil ftp server
  <ftp://ftp.yggdrasil.com/private/adam> where special patched versions
  of the kernel can be found.  Hopefully this will be rolled into the
  mainstream kernel in the near future.

  As of July, 23th 1997 Hans Reiser <mailto:reiser (at) RICOCHET.NET>
  has put up the source to his tree based reiserfs
  <http://idiom.com/~beverly/reiserfs.html> on the web. While his
  filesystem has some very interesting features and is much faster than
  ext2fs, it is still very experimental and difficult to integrate with
  the standard kernel. Expect some interesting developments in the
  future - this is different from your "average log based file system
  for Linux" project, because Hans already has working code.

  There is room for access control lists (ACL) and other unimplemented
  features in the existing ext2fs, stay tuned for future updates. There
  has been some talk about adding on the fly compression too.

  There is also an encrypted file system available but again as this is
  under export control from the US, make sure you get it from a legal
  place.

  File systems is an active field of academic and industrial research
  and development, the results of which are quite often freely
  available. Linux has in many cases been a development tool in such
  activities so you can expect a lot of continuous work in this field,
  stay tuned for the latest development.

  4.3.5.  CD-ROM File Systems

  There has been a number of file systems available for use on CD-ROM
  systems and one of the earliest one was the High Sierra format,
  supposedly named after the hotel where the final agreement took place.
  This was the precursor to the ISO 9660 format which is supported by
  Linux.  Later there were the Rock Ridge extensions which added file
  system features such as long filenames, permissions and more.

  The Linux iso9660 file system supports both High Sierra as well as
  Rock Ridge extensions.

  However, once again Microsoft decided it should create another
  standard and their latest effort here is called Joliet and offers some
  internationalisation features. This is at the time of writing not yet
  available in the standard kernel releases but exists in beta versions.
  Hopefully this should soon work its way into the standard kernel.

  In a recent Usenet News posting hpa (at) transmeta.com (H. Peter
  Anvin) writes the following the following interesting piece of trivia:

       Actually, Joliet is a city outside Chicago; best known for being the
       site of the prison where Elwood was locked up in the movie "Blues
       Brothers."  Rock Ridge (the UNIX extensions to ISO 9660) is named
       after the (fictional) town in the movie "Blazing Saddles."

  4.3.6.  Compression

  Disk versus file compression is a hotly debated topic especially
  regarding the added danger of file corruption. Nevertheless there are
  several options available for the adventurous administrators. These
  take on many forms, from kernel modules and patches to extra libraries
  but note that most suffer various forms of limitations such as being
  read-only. As development takes place at neck breaking speed the specs
  have undoubtedly changed by the time you read this. As always: check
  the latest updates yourself. Here only a few references are given.

  ╖  DouBle features file compression with some limitations.

  ╖  Zlibc adds transparent on-the-fly decompression of files as they
     load.

  ╖  there are many modules available for reading compressed files or
     partitions that are native to various other operating systems
     though currently most of these are read-only.

  ╖  dmsdos (currently in version 0.8.0a) offer many of the compression
     options available for DOS and Windows. It is not yet complete but
     work is ongoing and new features added regularly.

  Also there is the user file system (userfs) that allows FTP based file
  system and some compression (arcfs) plus fast prototyping and many
  other features.

  Recent kernels feature the loop or loopback device which can be used
  to put a complete file system within a file. There are some
  possibilities for using this for making new file systems with
  compression, tarring, encryption etc.

  Note that this device is unrelated to the network loopback device.

  Very recently a compression package that extends ext2fs was announced.
  It is still under testing and will therefore mainly be of interest for
  kernel hackers but should soon gain stability for wider use.

  4.3.7.  Physical Track Positioning

  This trick used to be very important when drives were slow and small,
  and some file systems used to take the varying characteristics into
  account when placing files. Although higher overall speed, on board
  drive and controller caches and intelligence has reduced the effect of
  this.

  Nevertheless there is still a little to be gained even today.  As we
  know, "world dominance" is soon within reach but to achieve this
  "fast" we need to employ all the tricks we can use

  To understand the strategy we need to recall this near ancient piece
  of knowledge and the properties of the various track locations.  This
  is based on the fact that transfer speeds generally increase for
  tracks further away from the spindle, as well as the fact that it is
  faster to seek to or from the central tracks than to or from the inner
  or outer tracks.

  Most drives use disks running at constant angular velocity but use
  (fairly) constant data density across all tracks. This means that you
  will get much higher transfer rates on the outer tracks than on the
  inner tracks; a characteristics which fits the requirements for large
  libraries well.

  Newer disks use a logical geometry mapping which differs from the
  actual physical mapping which is transparently mapped by the drive
  itself.  This makes the estimation of the "middle" tracks a little
  harder.

  In most cases track 0 is at the outermost track and this is the
  general assumption most people use. Still, it should be kept in mind
  that there are no guarantees this is so.

     Inner
        tracks are usually slow in transfer, and lying at one end of the
        seeking position it is also slow to seek to.

        This is more suitable to the low end directories such as DOS,
        root and print spools.
     Middle
        tracks are on average faster with respect to transfers than
        inner tracks and being in the middle also on average faster to
        seek to.

        This characteristics is ideal for the most demanding parts such
        as swap, /tmp and /var/tmp.

     Outer
        tracks have on average even faster transfer characteristics but
        like the inner tracks are at the end of the seek so
        statistically it is equally slow to seek to as the inner tracks.

        Large files such as libraries would benefit from a place here.

  Hence seek time reduction can be achieved by positioning frequently
  accessed tracks in the middle so that the average seek distance and
  therefore the seek time is short. This can be done either by using
  fdisk or cfdisk to make a partition on the middle tracks or by first
  making a file (using dd) equal to half the size of the entire disk
  before creating the files that are frequently accessed, after which
  the dummy file can be deleted. Both cases assume starting from an
  empty disk.

  The latter trick is suitable for news spools where the empty directory
  structure can be placed in the middle before putting in the data
  files.  This also helps reducing fragmentation a little.

  This little trick can be used both on ordinary drives as well as RAID
  systems. In the latter case the calculation for centring the tracks
  will be different, if possible. Consult the latest RAID manual.

  5.  Other Operating Systems

  Many Linux users have several operating systems installed, often
  necessitated by hardware setup systems that run under other operating
  systems, typically DOS or some flavour of Windows. A small section on
  how best to deal with this is therefore included here.

  5.1.  DOS

  Leaving aside the debate on weather or not DOS qualifies as an
  operating system one can in general say that it has little
  sophistication with respect to disk operations. The more important
  result of this is that there can be severe difficulties in running
  various versions of DOS on large drives, and you are therefore
  strongly recommended in reading the Large Drives mini-HOWTO. One
  effect is that you are often better off placing DOS on low track
  numbers.

  Having been designed for small drives it has a rather unsophisticated
  file system (FAT) which when used on large drives will allocate
  enormous block sizes. It is also prone to block fragmentation which
  will after a while cause excessive seeks and slow effective transfers.

  One solution to this is to use a defragmentation program regularly but
  it is strongly recommended to back up data and verify the disk before
  defragmenting. All versions of DOS have chkdsk that can do some disk
  checking, newer versions also have scandisk which is somewhat better.
  There are many defragmentation programs available, some versions have
  one called defrag. Norton Utilities have a large suite of disk tools
  and there are many others available too.

  As always there are snags, and this particular snake in our drive
  paradise is called hidden files. Some vendors started to use these for
  copy protection schemes and would not take kindly to being moved to a
  different place on the drive, even if it remained in the same place in
  the directory structure. The result of this was that newer
  defragmentation programs will not touch any hidden file, which in turn
  reduces the effect of defragmentation.

  Being a single tasking, single threading and single most other things
  operating system there is very little gains in using multiple drives
  unless you use a drive controller with built in RAID support of some
  kind.

  There are a few utilities called join and subst which can do some
  multiple drive configuration but there is very little gains for a lot
  of work. Some of these commands have been removed in newer versions.

  In the end there is very little you can do, but not all hope is lost.
  Many programs need fast, temporary storage, and the better behaved
  ones will look for environment variables called TMPDIR or TEMPDIR
  which you can set to point to another drive. This is often best done
  in autoexec.bat.

  ______________________________________________________________________
  SET TMPDIR=E:/TMP
  ______________________________________________________________________

  Not only will this possibly gain you some speed but also it can reduce
  fragmentation.

  There have been reports about difficulties in removing multiple
  primary partitions using the fdisk program that comes with DOS. Should
  this happen you can instead use a Linux rescue disk with Linux fdisk
  to repair the system.

  5.2.  Windows

  Most of the above points are valid for Windows too, with the exception
  of Windows95 which apparently has better disk handling, which will get
  better performance out of SCSI drives.

  A useful thing is the introduction of long filenames, to read these
  from Linux you will need the vfat file system for mounting these
  partitions.

  The most important thing is the introduction of the new file system
  FAT32 which is better suited to large drives. The snag is that there
  is very little support for this today, not even in NT 4.0 or many
  drive utility systems. A stable driver for Linux is coming soon but is
  not yet ready for prime time. Stay tuned for updates.

  Disk fragmentation is still a problem. Some of this can be avoided by
  doing a defragmentation immediately before and immediately after
  installing large programs or systems. I use this scheme at work and
  have found it to work quite well. Purging unused files and emptying
  the waste basket first can improve defragmentation further.

  Windows also use swap drives, redirecting this to another drive can
  give you some performance gains. There are several mini-HOWTOs telling
  you how best to share swap space between various operating systems.
  Very recently someone started a project supporting ext2fs support for
  Win95 which you can read about at this web site
  <http://www.globalxs.nl/home/p/pvs/>.

  5.3.  OS/2

  The only special note here is that you can get a file system driver
  for OS/2 that can read an ext2fs partition.

  5.4.  NT

  This is a more serious system featuring most buzzwords known to
  marketing.  It is well worth noting that it features software striping
  and other more sophisticated setups. Check out the drive manager in
  the control panel.  I do not have easy access to NT, more details on
  this can take a bit of time.

  One important snag was recently reported by acahalan at cs.uml.edu :
  (reformatted from a Usenet News posting)

  NT DiskManager has a serious bug that can corrupt your disk when you
  have several (more than one?) extended partitions.  Microsoft provides
  an emergency fix program at their web site. See the knowledge base
  <http://www.microsoft.com/kb/> for more.  (This affects Linux users,
  because Linux users have extra partitions)

  5.5.  Sun OS

  There is a little bit of confusion in this area between Sun OS vs.
  Solaris.  Strictly speaking Solaris is just Sun OS 5.x packaged with
  Openwindows and a few other things. If you run Solaris, just type
  uname -a to see your version. Parts of the reason for this confusion
  is that Sun Microsystems used to use an OS from the BSD family,
  albeight with a few bits and pieces from elsewhere as well as things
  made by themselves. This was the situation up to Sun OS 4.x.y when
  they did a "strategic roadmap decision" and decided to switch over to
  the official Unix, System V, Release 4 (aka SVR5), and Sun OS 5 was
  created.  This made a lot of people unhappy. Also this was bundled
  with other things and marketed under the name Solaris, which currently
  stands at release 2.6 beta.

  5.5.1.  Sun OS 4

  This is quite familiar to most Linux users. Note however that the file
  system structure is quite different and does not conform to FSSTND so
  any planning must be based on the traditional structure. You can get
  some information by the man page on this: man hier. This is, like most
  manpages, rather brief but should give you a good start. If you are
  still confused by the structure it will at least be at a higher level.

  5.5.2.  Sun OS 5 (aka Solaris)

  This comes with a snazzy installation system that runs under
  Openwindows, it will help you in partitioning and formatting the
  drives before installing the system from CD-ROM. It will also fail if
  your drive setup is too far out, and as it takes a complete
  installation run from a full CD-ROM in a 1x only drive this failure
  will dawn on you after too long time. That is the experience we had
  where I work. Instead we installed everything onto one drive and then
  moved directories across.

  The default settings are sensible for most things, yet there remains a
  little oddity: swap drives. Even though the official manual recommends
  multiple swap drives (which are used in a similar fashion as on Linux)
  the default is to use only a single drive. It is recommended to change
  this as soon as possible.

  Sun OS 5 offers also a file system especially designed for temporary
  files, tmpfs. This is a kind of souped up RAM disk, and like ordinary
  RAM disks the contents is lost when the power goes. If space is scarce
  parts of the pseudo drive is swapped out, so in effect you store
  temporary files on the swap partition. Linux does not have such a file
  system; it has been discussed in the past but opinions were mixed. I
  would be interested in hearing comments on this.

  Also see the note on ``Combining swap and /tmp''.

  Trivia: There is a movie also called Solaris, a science fiction movie
  that is very, very long, slow and incomprehensible. This was often
  pointed out at the time Solaris (the OS) appeared...

  6.  Clusters

  In this section I will briefly touch on the ways machines can be
  connected together but this is so big a topic it could be a separate
  HOWTO in its own right, hint, hint. Also, strictly speaking, this
  section lies outside the scope of this HOWTO, so if you feel like
  getting fame etc. you could contact me and take over this part and
  turn it into a new document.

  These days computers gets outdated at an incredible rate. There is
  however no reason why old hardware could not be put to good use with
  Linux. Using an old and otherwise outdated computer as a network
  server can be both useful in its own right as well as a valuable
  educational exercise. Such a local networked cluster of computers can
  take on many forms but to remain within the charter of this HOWTO I
  will limit myself to the disk strategies.  Nevertheless I would hope
  someone else could take on this topic and turn it into a document on
  its own.

  This is an exciting area of activity today, and many forms of
  clustering is available today, ranging from automatic workload
  balancing over local network to more exotic hardware such as Scalable
  Coherent Interface (SCI) which gives a tight integration of machines,
  effectively turning them into a single machine. Various kinds of
  clustering has been available for larger machines for some time and
  the VAXcluster is perhaps a well known example of this. Clustering is
  done usually in order to share resources such as disk drives, printers
  and terminals etc, but also processing resources equally transparently
  between the computational nodes.

  There is no universal definition of clustering, in here it is taken to
  mean a network of machines that combine their resources to serve
  users. Admittedly this is a rather loose definition but this will
  change later.

  These days also Linux offers some clustering features but for a
  starter I will just describe a simple local network. It is a good way
  of putting old and otherwise unusable hardware to good use, as long as
  they can run Linux or something similar.

  One of the best ways of using an old machine is as a network server in
  which case the effective speed is more likely to be limited by network
  bandwidth rather than pure computational performance. For home use you
  can move the following functionality off to an older machine used as a
  server:

  ╖  news

  ╖  mail

  ╖  web proxy

  ╖  printer server

  ╖  modem server (PPP, SLIP, FAX, Voice mail)

  You can also NFS mount drives from the server onto your workstation
  thereby reducing drive space requirements. Still read the FSSTND to
  see what directories should not be exported. The best candidates for
  exporting to all machines are /usr and /var/spool and possibly
  /usr/local

  Most of the time even slow disks will deliver sufficient performance.
  On the other hand, if you do processing directly on the disks on the
  server or have very fast networking, you might want to rethink your
  strategy and use faster drives. Searching features on a web server or
  news database searches are two examples of this.

  Such a network can be an excellent way of learning system
  administration and building up your own toaster network, as it often
  is called. You can get more information on this in other HOWTOs but
  there are two important things you should keep in mind:

  ╖  Do not pull IP numbers out of thin air. Configure your inside net
     using IP numbers reserved for private use, and use your network
     server as a router that handles this IP masquerading.

  ╖  Remember that if you additionally configure the router as a
     firewall you might not be able to get to your own data from the
     outside, depending on the firewall configuration.

  The nyx network provides an example of a cluster in the sense defined
  here.  It consists of the following machines:

     nyx
        is one of the two user login machines and also provides some of
        the networking services.

     nox
        (aka nyx10) is the main user login machine and is also the mail
        server.

     noc
        is a dedicated news server. The news spool is made accessible
        through NFS mounting to nyx and nox.

     arachne
        (aka www) is the web server. Web pages are written by NFS
        mounting onto nox.

  There are also some more advanced clustering projects going, notably

  ╖  The Beowolf Project
     <http://cesdis.gsfc.nasa.gov/linux/beowulf/beowulf.html>

  ╖  The Genoa Active Message Machine (GAMMA)
     <http://www.disi.unige.it/project/gamma/>

  High-tech clustering requires high-tech interconnect, and SCI is one
  of them.  To find out more you can either look up the home page of
  Dolphin Interconnect Solutions <http://www.dolphinics.no/> which is
  one of the main actors in this field, or you can have a look at scizzl
  <http://www.scizzl.com/>.

  7.  Mount Points

  In designing the disk layout it is important not to split off the
  directory tree structure at the wrong points, hence this section.  As
  it is highly dependent on the FSSTND it has been put aside in a
  separate section, and will most likely have to be totally rewritten
  when FHS is released. Nobody knows when that will happen, and at the
  time of writing this a debate of near-religious qualities is taking
  place on the mailing list. In the meanwhile this will do.

  Remember that this is a list of where a separation can take place, not
  where it has to be. As always, good judgement is always required.

  Again only a rough indication can be given here. The values indicate

       0=don't separate here
       1=not recommended
        ...
       4=useful
       5=recommended

  In order to keep the list short, the uninteresting parts are removed.

  Directory   Suitability
  /
  |
  +-bin       0
  +-boot      0
  +-dev       0
  +-etc       0
  +-home      5
  +-lib       0
  +-mnt       0
  +-proc      0
  +-root      0
  +-sbin      0
  +-tmp       5
  +-usr       5
  | \
  | +-X11R6     3
  | +-bin       3
  | +-lib       4
  | +-local     4
  | | \
  | | +bin        2
  | | +lib        4
  | +-src       3
  |
  +-var       5
    \
    +-adm       0
    +-lib       2
    +-lock      1
    +-log       1
    +-preserve  1
    +-run       1
    +-spool     4
    | \
    | +-mail      3
    | +-mqueue    3
    | +-news      5
    | +-smail     3
    | +-uucp      3
    +-tmp       5

  There is of course plenty of adjustments possible, for instance a home
  user would not bother with splitting off the /var/spool hierarchy but
  a serious ISP should. The key here is usage.

  8.  Disk Layout

  With all this in mind we are now ready to embark on the layout. I have
  based this on my own method developed when I got hold of 3 old SCSI
  disks and boggled over the possibilities.

  The tables in the appendices are designed to simplify the mapping
  process. They have been designed to help you go through the process of
  optimizations as well as making an useful log in case of system
  repair. A few examples are also given.

  8.1.  Selection for partitioning

  Determine your needs and set up a list of all the parts of the file
  system you want to be on separate partitions and sort them in
  descending order of speed requirement and how much space you want to
  give each partition.

  The table in Appendix A `` '' is a useful tool to select what
  directories you should put on different partitions. It is sorted in a
  logical order with space for your own additions and notes about
  mounting points and additional systems. It is therefore NOT sorted in
  order of speed, instead the speed requirements are indicated by
  bullets ('o').

  If you plan to RAID make a note of the disks you want to use and what
  partitions you want to RAID. Remember various RAID solutions offers
  different speeds and degrees of reliability.

  (Just to make it simple I'll assume we have a set of identical SCSI
  disks and no RAID)

  8.2.  Mapping partitions to drives

  Then we want to place the partitions onto physical disks. The point of
  the following algorithm is to maximise parallelizing and bus capacity.
  In this example the drives are A, B and C and the partitions are
  987654321 where 9 is the partition with the highest speed requirement.
  Starting at one drive we 'meander' the partition line over and over
  the drives in this way:

               A : 9 4 3
               B : 8 5 2
               C : 7 6 1

  This makes the 'sum of speed requirements' the most equal across each
  drive.

  Use the table in Appendix B `` '' to select what drives to use for
  each partition in order to optimize for parallelicity.

  Note the speed characteristics of your drives and note each directory
  under the appropriate column. Be prepared to shuffle directories,
  partitions and drives around a few times before you are satisfied.

  8.3.  Sorting partitions on drives

  After that it is recommended to select partition numbering for each
  drive.

  Use the table in Appendix C `` '' to select partition numbers in order
  to optimize for track characteristics.  At the end of this you should
  have a table sorted in ascending partition number. Fill these numbers
  back into the tables in appendix A and B.

  You will find these tables useful when running the partitioning
  program (fdisk or cfdisk) and when doing the installation.

  8.4.  Optimizing

  After this there are usually a few partitions that have to be
  'shuffled' over the drives either to make them fit or if there are
  special considerations regarding speed, reliability, special file
  systems etc. Nevertheless this gives what this author believes is a
  good starting point for the complete setup of the drives and the
  partitions. In the end it is actual use that will determine the real
  needs after we have made so many assumptions. After commencing
  operations one should assume a time comes when a repartitioning will
  be beneficial.

  For instance if one of the 3 drives in the above mentioned example is
  very slow compared to the two others a better plan would be as
  follows:

               A : 9 6 5
               B : 8 7 4
               C : 3 2 1

  8.4.1.  Optimizing by characteristics

  Often drives can be similar in apparent overall speed but some
  advantage can be gained by matching drives to the file size
  distribution and frequency of access. Thus binaries are suited to
  drives with fast access that offer command queueing, and libraries are
  better suited to drives with larger transfer speeds where IDE offers
  good performance for the money.

  8.4.2.  Optimizing by drive parallelising

  Avoid drive contention by looking at tasks: for instance if you are
  accessing /usr/local/bin chances are you will soon also need files
  from /usr/local/lib so placing these at separate drives allows less
  seeking and possible parallel operation and drive caching. It is quite
  possible that choosing what may appear less than ideal drive
  characteristics will still be advantageous if you can gain parallel
  operations. Identify common tasks, what partitions they use and try to
  keep these on separate physical drives.

  Just to illustrate my point I will give a few examples of task
  analysis here.

     Office software
        such as editing, word processing and spreadsheets are typical
        examples of low intensity software both in terms of CPU and disk
        intensity. However, should you have a single server for a huge
        number of users you should not forget that most such software
        have auto save facilities which cause extra traffic, usually on
        the home directories. Splitting users over several drives would
        reduce contention.

     News
        readers also feature auto save features on home directories so
        ISPs should consider separating home directories

        News spools are notorious for their deeply nested directories
        and their large number of very small files. Loss of a news spool
        partition is not a big problem for most people, too, so they are
        good candidates for a RAID 0 setup with many small disks to
        distribute the many seeks among multiple spindles. It is
        recommended in the manuals and FAQs for the INN news server to
        put news spool and .overview files on separate drives for larger
        installations.

        There is also a web page dedicated to INN optimising
        <http://www.spinne.com/usenet/inn-perf.html> well worth reading.

     Database
        applications can be demanding both in terms of drive usage and
        speed requirements. The details are naturally application
        specific, read the documentation carefully with disk
        requirements in mind. Also consider RAID both for performance
        and reliability.

     E-mail
        reading and sending involves home directories as well as in- and
        outgoing spool files. If possible keep home directories and
        spool files on separate drives. If you are a mail server or a
        mail hub consider putting in- and outgoing spool directories on
        separate drives.

        Losing mail is an extremely bad thing, if you are and ISP or
        major hub. Think about RAIDing your mail spool and consider
        frequent backups.

     Software development
        can require a large number of directories for binaries,
        libraries, include files as well as source and project files. If
        possible split as much as possible across separate drives. On
        small systems you can place /usr/src and project files on the
        same drive as the home directories.

     Web browsing
        is becoming more and more popular. Many browsers have a local
        cache which can expand to rather large volumes. As this is used
        when reloading pages or returning to the previous page, speed is
        quite important here. If however you are connected via a well
        configured proxy server you do not need more than typically a
        few megabytes per user for a session.  See also the sections on
        ``Home Directories'' and ``WWW''.

  8.5.  Usage requirements

  When you get a box of 10 or so CD-ROMs with a Linux distribution and
  the entire contents of the big FTP sites it can be tempting to install
  as much as your drives can take. Soon, however, one would find that
  this leaves little room to grow and that it is easy to bite over more
  than can be chewed, at least in polite company. Therefore I will make
  a few comments on a few points to keep in mind when you plan out your
  system. Comments here are actively sought.
     Testing
        Linux is simple and you don't even need a hard disk to try it
        out, if you can get the boot floppies to work you are likely to
        get it to work on your hardware. If the standard kernel does not
        work for you, do not forget that often there can be special boot
        disk versions available for unusual hardware combinations that
        can solve your initial problems until you can compile your own
        kernel.

     Learning
        about operating system is something Linux excels in, there is
        plenty of documentation and the source is available. A single
        drive with 50MB is enough to get you started with a shell, a few
        of the most frequently used commands and utilities.

     Hobby
        use or more serious learning requires more commands and
        utilities but a single drive is still all it takes, 500MB should
        give you plenty of room, also for sources and documentation.

     Serious
        software development or just serious hobby work requires even
        more space. At this stage you have probably a mail and news feed
        that requires spool files and plenty of space. Separate drives
        for various tasks will begin to show a benefit. At this stage
        you have probably already gotten hold of a few drives too. Drive
        requirements gets harder to estimate but I would expect 2-4GB to
        be plenty, even for a small server.

     Servers
        come in many flavours, ranging from mail servers to full sized
        ISP servers. A base of 2GB for the main system should be
        sufficient, then add space and perhaps also drives for separate
        features you will offer. Cost is the main limiting factor here
        but be prepared to spend a bit if you wish to justify the "S" in
        ISP. Admittedly, not all do it.

  8.6.  Servers

  Big tasks require big drives and a separate section here. If possible
  keep as much as possible on separate drives. Some of the appendices
  detail the setup of a small departmental server for 10-100 users. Here
  I will present a few consideration for the higher end servers. In
  general you should not be afraid of using RAID, not only because it is
  fast and safe but also because it can make growth a little less
  painful. All the notes below come as additions to the points mentioned
  earlier.

  Popular servers rarely just happens, rather they grow over time and
  this demands both generous amounts of disk space as well as a good net
  connection.  In many of these cases it might be a good idea to reserve
  entire SCSI drives, in singles or as arrays, for each task. This way
  you can move the data should the computer fail. Note that transferring
  drives across computers is not simple and might not always work,
  especially in the case of IDE drives. Drive arrays require careful
  setup in order to reconstruct the data correctly, so you might want to
  keep a paper copy of your fstab file as well as a note of SCSI IDs.

  8.6.1.  Home directories

  Estimate how many drives you will need, if this is more than 2 I would
  recommend RAID, strongly. If not you should separate users across your
  drives dedicated to users based on some kind of simple hashing
  algorithm.  For instance you could use the first 2 letters in the user
  name, so jbloggs is put on /u/j/b/jbloggs where /u/j is a symbolic
  link to a physical drive so you can get a balanced load on your
  drives.

  8.6.2.  Anonymous FTP

  This is an essential service if you are serious about service. Good
  servers are well maintained, documented, kept up to date, and
  immensely popular no matter where in the world they are located. The
  big server ftp.funet.fi is an excellent example of this.

  In general this is not a question of CPU but of network bandwidth.
  Size is hard to estimate, mainly it is a question of ambition and
  service attitudes. I believe the big archive at ftp.cdrom.com is a
  *BSD machine with 50GB disk. Also memory is important for a dedicated
  FTP server, about 256MB RAM would be sufficient for a very big server,
  whereas smaller servers can get the job done well with 64MB RAM.
  Network connections would still be the most important factor.

  8.6.3.  WWW

  For many this is the main reason to get onto the Internet, in fact
  many now seem to equate the two. In addition to being network
  intensive there is also a fair bit of drive activity related to this,
  mainly regarding the caches. Keeping the cache on a separate, fast
  drive would be beneficial. Even better would be installing a caching
  proxy server. This way you can reduce the cache size for each user and
  speed up the service while at the same time cut down on the bandwidth
  requirements.

  With a caching proxy server you need a fast set of drives, RAID0 would
  be ideal as reliability is not important here. Higher capacity is
  better but about 2GB should be sufficient for most. Remember to match
  the cache period to the capacity and demand. Too long periods would on
  the other hand be a disadvantage, if possible try to adjust based on
  the URL. For more information check up on the most used servers such
  as Harvest, Squid <http://www.nlanr.net/Squid> and the one from
  Netscape.

  8.6.4.  Mail

  Handling mail is something most machines do to some extent. The big
  mail servers, however, come into a class of their own. This is a
  demanding task and a big server can be slow even when connected to
  fast drives and a good net feed. In the Linux world the big server at
  vger.rutgers.edu is a well known example. Unlike a news service which
  is distributed and which can partially reconstruct the spool using
  other machines as a feed, the mail servers are centralised. This makes
  safety much more important, so for a major server you should consider
  a RAID solution with emphasize on reliability. Size is hard to
  estimate, it all depends on how many lists you run as well as how many
  subscribers you have.

  8.6.5.  News

  This is definitely a high volume task, and very dependent on what news
  groups you subscribe to. On Nyx there is a fairly complete feed and
  the spool files consume about 17GB. The biggest groups are no doubt in
  the alt.binary.* hierarchy, so if you for some reason decide not to
  get these you can get a good service with perhaps 12GB. Still others,
  that shall remain nameless, feel 2GB is sufficient to claim ISP
  status.  In this case news expires so fast I feel the spelling IsP is
  barely justified.

  8.6.6.  Others

  There are many services available on the net and even though many have
  been put somewhat in the shadows by the web. Nevertheless, services
  like archie, gopher and wais just to name a few, still exist and
  remain valuable tools on the net. If you are serious about starting a
  major server you should also consider these services. Determining the
  required volumes is hard, it all depends on popularity and demand.
  Providing good service inevitably has its costs, disk space is just
  one of them.

  8.7.  Pitfalls

  The dangers of splitting up everything into separate partitions are
  briefly mentioned in the section about volume management. Still,
  several people have asked me to emphasize this point more strongly:
  when one partition fills up it cannot grow any further, no matter if
  there is plenty of space in other partitions.

  In particular look out for explosive growth in the news spool
  (/var/spool/news). For multi user machines with quotas keep an eye on
  /tmp and /var/tmp as some people try to hide their files there, just
  look out for filenames ending in gif or jpeg...

  In fact, for single physical drives this scheme offers very little
  gains at all, other than making file growth monitoring easier (using
  'df') and physical track positioning. Most importantly there is no
  scope for parallel disk access. A freely available volume management
  system would solve this but this is still some time in the future.
  However, when more specialised file systems become available even a
  single disk could benefit from being divided into several partitions.

  8.8.  Compromises

  One way to avoid the aforementioned pitfalls is to only set off fixed
  partitions to directories with a fairly well known size such as swap,
  /tmp and /var/tmp and group together the remainders into the remaining
  partitions using symbolic links.

  Example: a slow disk (slowdisk), a fast disk (fastdisk) and an
  assortment of files. Having set up swap and tmp on fastdisk; and /home
  and root on slowdisk we have (the fictitious) directories /a/slow,
  /a/fast, /b/slow and /b/fast left to allocate on the partitions
  /mnt.slowdisk and /mnt.fastdisk which represents the remaining
  partitions of the two drives.

  Putting /a or /b directly on either drive gives the same properties to
  the subdirectories. We could make all 4 directories separate
  partitions but would lose some flexibility in managing the size of
  each directory. A better solution is to make these 4 directories
  symbolic links to appropriate directories on the respective drives.
  Thus we make

       /a/fast point to /mnt.fastdisk/a/fast   or   /mnt.fastdisk/a.fast
       /a/slow point to /mnt.slowdisk/a/slow   or   /mnt.slowdisk/a.slow
       /b/fast point to /mnt.fastdisk/b/fast   or   /mnt.fastdisk/b.fast
       /b/slow point to /mnt.slowdisk/b/slow   or   /mnt.slowdisk/b.slow

  and we get all fast directories on the fast drive without having to
  set up a partition for all 4 directories. The second (right hand)
  alternative gives us a flatter files system which in this case can
  make it simpler to keep an overview of the structure.

  The disadvantage is that it is a complicated scheme to set up and plan
  in the first place and that all mount point and partitions have to be
  defined before the system installation.

  9.  Implementation

  Having done the layout you should now have a detailled description on
  what goes where. Most likely this will be on paper but hopefully
  someone will make a more automated system that can deal with
  everything from the design, through partitioning to formatting and
  installation. This is the route one will have to take to realise the
  design.

  Modern distributions come with installation tools that will guide you
  through partitioning and formatting and also set up /etc/fstab for you
  automatically. For later modifications, however, you will need to
  understand the underlying mechanisms.

  9.1.  Drives and Partitions

  When you start DOS or the like you will find all partitions labeled C:
  and onwards, with no differentiation on IDE, SCSI, network or whatever
  type of media you have. In the world of Linux this is rather
  different. During booting you will see partitions described like this:

  ______________________________________________________________________
  Dec  6 23:45:18 demos kernel: Partition check:
  Dec  6 23:45:18 demos kernel:  sda: sda1
  Dec  6 23:45:18 demos kernel:  hda: hda1 hda2
  ______________________________________________________________________

  SCSI drives are labelled sda, sdb, sdc etc, and (E)IDE drives are
  labelled hda, hdb, hdc etc.  There are also standard names for all
  devices, full information can be found in /dev/MAKEDEV and
  /usr/src/linux/Documentation/devices.txt.

  Partitions are labelled numerically for each drive hda1, hda2 and so
  on.  On SCSI drives there can be 15 partitions per drive, on EIDE
  drives there can be 63 partitions per drive. Both limits exceed what
  is currently useful for most disks.

  These are then mounted according to the file /etc/fstab before they
  appear as a part of the file system.
  9.2.  Partitioning

  First you have to partition each drive into a number of separate
  partitions.  Under Linux there are two main methods, fdisk and the
  more screen oriented cfdisk. These are complex programs, read the
  manual very carefully. Under DOS there are other choices, mainly the
  version of fdisk that is bundled with for instance DOS, or fips. The
  latter has the unique advantage here that it can repartition a drive
  without necessarily damaging existing data, unlike all the other
  partitioning programs.

  In order to get the most out of fips you should first defragment your
  drive. This way you can allocate more space to other partitions.

  Nevertheless, it is important you do a full backup of all your valued
  data before partitioning.

  Partitions come in 3 flavours, primary, extended and logical.  You
  have to use primary partitions for booting, but there is a maximum of
  4 primary partitions. If you want more you have to define an extended
  partition within which you define your logical partitions.

  Each partition has an identifier number which tells the operating
  system what it is, for Linux the types swap and ext2fs are the ones
  you will need to know.

  There is a readme file that comes with fdisk that gives more in-depth
  information on partitioning.

  Someone has just made a Partitioning HOWTO which contains excellent,
  in depth information on the nitty-gritty of partitioning. Rather than
  repeating it here and bloating this document further, I will instead
  refer you to it instead.

  9.3.  Multiple devices (md)

  Being in a state of flux you should make sure to read the latest
  documentation on this kernel feature. It is not yet stable, beware.

  Briefly explained it works by adding partitions together into new
  devices md0, md1 etc. using mdadd before you activate them using
  mdrun. This process can be automated using the file /etc/mdtab.

  Then you then treat these like any other partition on a drive. Proceed
  with formatting etc. as described below using these new devices.

  There is now also a HOWTO in development for RAID using md you should
  read.

  9.4.  Formatting

  Next comes partition formatting, putting down the data structures that
  will describe the files and where they are located. If this is the
  first time it is recommended you use formatting with verify. Strictly
  speaking it should not be necessary but this exercises the I/O hard
  enough that it can uncover potential problems, such as incorrect
  termination, before you store your precious data. Look up the command
  mkfs for more details.

  Linux can support a great number of file systems, rather than
  repeating the details you can read the manpage for fs which describes
  them in some details. Note that your kernel has to have the drivers
  compiled in or made as modules in order to be able to use these
  features. When the time comes for kernel compiling you should read
  carefully through the file system feature list. If you use make
  menuconfig you can get online help for each file system type.

  Note that some rescue disk systems require minix, msdos and ext2fs to
  be compiled into the kernel.

  Also swap partitions have to be prepared, and for this you use mkswap.

  9.5.  Mounting

  Data on a partition is not available to the file system until it is
  mounted on a mount point. This can be done manually using mount or
  automatically during booting by adding appropriate lines to
  /etc/fstab. Read the manual for mount and pay close attention to the
  tabulation.

  10.  Maintenance

  It is the duty of the system manager to keep an eye on the drives and
  partitions. Should any of the partitions overflow, the system is
  likely to stop working properly, no matter how much space is available
  on other partitions, until space is reclaimed.

  Partitions and disks are easily monitored using df and should be done
  frequently, perhaps using a cron job or some other general system
  management tool.

  Do not forget the swap partitions, these are best monitored using one
  of the memory statistics programs such as free, procinfo or top.

  Drive usage monitoring is more difficult but it is important for the
  sake of performance to avoid contention - placing too much demand on a
  single drive if others are available and idle.

  It is important when installing software packages to have a clear idea
  where the various files go. As previously mentioned GCC keeps binaries
  in a library directory and there are also other programs that for
  historical reasons are hard to figure out, X11 for instance has an
  unusually complex structure.

  When your system is about to fill up it is about time to check and
  prune old logging messages as well as hunt down core files. Proper use
  of ulimit in global shell settings can help saving you from having
  core files littered around the system.

  10.1.  Backup

  The observant reader might have noticed a few hints about the
  usefulness of making backups. Horror stories are legio about accidents
  and what happened to the person responsible when the backup turned out
  to be non-functional or even non existent. You might find it simpler
  to invest in proper backups than a second, secret identity.

  There are many options and also a mini-HOWTO ( Backup-With-MSDOS )
  detailling what you need to know. In addition to the DOS specifics it
  also contains general information and further leads.

  In addition to making these backups you should also make sure you can
  restore the data. Not all systems verify that the data written is
  correct and many administrators have started restoring the system
  after an accident happy in the belief that everything is working, only
  to discover to their horror that the backups were useless. Be careful.

  10.2.  Defragmentation

  This is very dependent on the file system design, some suffer fast and
  nearly debilitating fragmentation. Fortunately for us, ext2fs does not
  belong to this group and therefore there has been very little talk
  about making a defragmentation tool.

  If for some reason you feel this is necessary, the quick and easy
  solution is to do a backup and a restore. If only a small area is
  affected, for instance the home directories, you could tar it over to
  a temporary area on another partition, verify the archive, delete the
  original and then untar it back again.

  10.3.  Deletions

  Quite often disk space shortages can be remedied simply by deleting
  unnecessary files that accumulate around the system. Quite often
  programs that terminate abnormally cause all kinds of mess lying
  around the oddest places. Normally a core dump results after such an
  incident and unless you are going to debug it you can simply delete
  it. These can be found everywhere so you are advised to do a global
  search for them now and then.

  Unexpected termination can also cause all sorts of temporary files
  remaining in places like /tmp or /var/tmp, files that are
  automatically removed when the program ends normally. Rebooting cleans
  up some of these areas but not necessary all and if you have a long
  uptime you could end up with a lot of old junk. If space is short you
  have to delete with care, make sure the file is not in active use
  first. Utilities like file can often tell you what kind of file you
  are looking at.

  Many things are logged when the system is running, mostly to files in
  the /var/log area. In particular the file /var/log/messages tends to
  grow until deleted. It is a good idea to keep a small archive of old
  log files around for comparison should the system start to behave
  oddly.

  If the mail or news system is not working properly you could have
  excessive growth in their spool areas, /var/spool/mail and
  /var/spool/news respectively. Beware of the overview files as these
  have a leading dot which makes them invisible to ls -l, it is always
  better to use ls -Al which will reveal them.

  User space overflow is a particularly tricky topic. Wars have been
  waged between system administrators and users. Tact, diplomacy and a
  generous budget for new drives is what is needed. Make use of the
  message-of-the-day feature, information displayed during login from
  the /etc/motd file to tell users when space is short.  Setting the
  default shell settings to prevent core files being dumped can save you
  a lot of work too.

  Certain kinds of people try to hide files around the system, usually
  trying to take advantage of the fact that files with a leading dot in
  the name are invisible to the ls command.  One common example are
  files that look like ... that normally either are not seen, or, when
  using ls -al disappear in the noise of normal files like . or .. that
  are in every directory.  There is however a countermeasure to this,
  use ls -Al that suppresses . or .. but shows all other dot-files.

  10.4.  Upgrades

  No matter how large your drives, time will come when you will find you
  need more. As technology progresses you can get ever more for your
  money. At the time of writing this, it appears that 5GB drives gives
  you the most bang for your bucks.

  Note that with IDE drives you might have to remove an old drive, as
  the maximum number supported on your mother board is normally only 2
  or some times 4. With SCSI you can have up to 7 for narrow (8-bit)
  SCSI or up to 15 for wide (15 bit) SCSI, per channel. Some host
  adapters can support more than a single channel and in any case you
  can have more than one host adapter per system. My personal
  recommendation is that you will most likely be better off with SCSI in
  the long run.

  The question comes, where should you put this new drive? In many cases
  the reason for expansion is that you want a larger spool area, and in
  that case the fast, simple solution is to mount the drive somewhere
  under /var/spool. On the other hand newer drives are likely to be
  faster than older ones so in the long run you might find it worth your
  time to do a full reorganizing, possibly using your old design sheets.

  If the upgrade is forced by running out of space in partitions used
  for things like /usr or /var the upgrade is a little more involved.
  You might consider the option of a full re-installation from your
  favourite (and hopefully upgraded) distribution. In this case you will
  have to be careful not to overwrite your essential setups. Usually
  these things are in the /etc directory. Proceed with care, fresh
  backups and working rescue disks. The other possibility is to simply
  copy the old directory over to the new directory which is mounted on a
  temporary mount point, edit your /etc/fstab file, reboot with your new
  partition in place and check that it works.  Should it fail you can
  reboot with your rescue disk, re-edit /etc/fstab and try again.

  Until volume management becomes available to Linux this is both
  complicated and dangerous. Do not get too surprised if you discover
  you need to restore your system from a backup.

  The Tips-HOWTO gives the following example on how to move an entire
  directory structure across:

  ______________________________________________________________________
  (cd /source/directory; tar cf - . ) | (cd /dest/directory; tar xvfp -)
  ______________________________________________________________________

  While this approach to moving directory trees is portable among many
  Unix systems, it is inconvenient to remember. Also, it fails for
  deeply nested directory trees when pathnames become to long to handle
  for tar (GNU tar has special provisions to deal with long pathnames).

  If you have access to GNU cp (which is always the case on Linux
  systems), you could as well use

  ______________________________________________________________________
  cp -av /source/directory /dest/directory
  ______________________________________________________________________

  GNU cp knows specifically about symbolic links, FIFOs and device files
  and will copy them correctly.

  11.  Advanced Issues

  Linux and related systems offer plenty of possibilities for fast,
  efficient and devastating destruction. This document is no exception.
  With power comes dangers and the following sections describe a few
  more esoteric issues that should not be attempted before reading and
  understanding the documentation, the issues and the dangers. You
  should also make a backup. Also remember to try to restore the system
  from scratch from your backup at least once.  Otherwise you might not
  be the first to be found with a perfect backup of your system and no
  tools available to reinstall it (or, even more embarrassing, some
  critical files missing on tape).

  The techniques described here are rarely necessary but can be used for
  very specific setups. Think very clearly through what you wish to
  accomplish before playing around with this.

  11.1.  Hard Disk Tuning

  The hard drive parameters can be tuned using the hdparms utility. Here
  the most interesting parameter is probably the read-ahead parameter
  which determines how much prefetch should be done in sequential
  reading.

  If you want to try this out it makes most sense to tune for the
  characteristic file size on your drive but remember that this tuning
  is for the entire drive which makes it a bit more difficult. Probably
  this is only of use on large servers using dedicated news drives etc.

  11.2.  File System Tuning

  Most file systems come with a tuning utility and for ext2fs there is
  the tune2fs utility. Several parameters can be modified but perhaps
  the most useful parameter here is what size should be reserved and who
  should be able to take advantage of this which could help you getting
  more useful space out of your drives, possibly at the cost of less
  room for repairing a system should it crash.

  11.3.  Spindle Synchronizing

  This should not in itself be dangerous, other than the peculiar fact
  that the exact details of the connections remain unclear for many
  drives. The theory is simple: keeping a fixed phase difference between
  the different drives in a RAID setup makes for less waiting for the
  right track to come into position for the read/write head. In practice
  it now seems that with large read-ahead buffers in the drives the
  effect is negligible.

  12.  Further Information

  There is wealth of information one should go through when setting up a
  major system, for instance for a news or general Internet service
  provider.  The FAQs in the following groups are useful:

  12.1.  News groups

  Some of the most interesting news groups are:

  ╖  Storage <news:comp.arch.storage>.

  ╖  PC storage <news:comp.sys.ibm.pc.hardware.storage>.

  ╖  AFS <news:alt.filesystems.afs>.

  ╖  SCSI <news:comp.periphs.scsi>.

  ╖  Linux setup <news:comp.os.linux.setup>.

  Most newsgroups have their own FAQ that are designed to answer most of
  your questions, as the name Frequently Asked Questions indicate. Fresh
  versions should be posted regularly to the relevant newsgroups. If you
  cannot find it in your news spool you could go directly to the FAQ
  main archive FTP site <ftp://rtfm.mit.edu>. The WWW versions can be
  browsed at FAQ main archive WWW site <http://www.cis.ohio-
  state.edu/hypertext/faq/usenet/FAQ-List.html>.

  Some FAQs have their own home site, of particular interest here are
  SCSI FAQ <http://www.paranoia.com/~filipg/HTML/LINK/F_SCSI.html> and
  comp.arch.storage FAQ
  <http://alumni.caltech.edu/~rdv/comp_arch_storage/FAQ-1.html>.

  12.2.  Mailing lists

  These are low noise channels mainly for developers. Think twice before
  asking questions there as noise delays the development.  Some relevant
  lists are linux-raid, linux-scsi and linux-ext2fs.  Many of the most
  useful mailing lists run on the vger.rutgers.edu server but this is
  notoriously overloaded, so try to find a mirror. There are some lists
  mirrored at The Redhat Home Page <http://www.redhat.com>.  Many lists
  are also accessible at linuxhq <http://www.linuxhq.com/lnxlists>, and
  the rest of the web site is a gold mine of useful information.

  If you want to find out more about the lists available you can send a
  message with the line lists to the list server at vger.rutgers.edu
  <mailto:[e-mail]>.  If you need help on how to use
  the mail server just send the line help to the same address.  Due to
  the popularity of this server it is likely it takes a bit to time
  before you get a reply or even get messages after you send a subscribe
  command.

  There is also a number of other majordomo list servers that can be of
  interest such as the EATA driver list <mailto:[e-mail]-
  mainz.de> and the Intelligent IO list <mailto:[e-mail]>.

  Mailing lists are in a state of flux but you can find links to a
  number of interesting lists from the Linux Documentation Homepage
  <http://sunsite.unc.edu/LDP>.

  12.3.  HOWTO

  These are intended as the primary starting points to get the
  background information as well as show you how to solve a specific
  problem.  Some relevant HOWTOs are Bootdisk, Installation,  SCSI and
  UMSDOS.  The main site for these is the LDP archive
  <http://sunsite.unc.edu/LDP> at Sunsite.

  12.4.  Mini-HOWTO

  These are the smaller free text relatives to the HOWTOs.  Some
  relevant mini-HOWTOs are Backup-With-MSDOS, Diskless, LILO,
  Linux+DOS+Win95+OS2, Linux+OS2+DOS, Linux+Win95, NFS-Root,
  Win95+Win+Linux, ZIP Drive .  You can find these at the same place as
  the HOWTOs, usually in a sub directory called mini. Note that these
  are scheduled to be converted into SGML and become proper HOWTOs in
  the near future.

  The old Linux Large IDE mini-HOWTO is no longer valid, instead read
  /usr/src/linux/drivers/block/README.ide or
  /usr/src/linux/Documentation/ide.txt.

  12.5.  Local resources

  In most distributions of Linux there is already a document directory
  already, have a look in the document archive <file:///usr/doc> where
  most packages store their main documentation and README files etc.
  Also you will here find the HOWTO archive <file:///usr/doc/HOWTO> of
  ready formatted HOWTOs and also the mini-HOWTO archive
  <file:///usr/doc/HOWTO/mini> of plain text documents.

  Many of the configuration files mentioned earlier can be found in the
  etc <file:///etc> directory. In particular you will want to work with
  the fstab <file:///etc/fstab> file that sets up the mounting of
  partitions and possibly also mdtab <file:///etc/mdtab> file that is
  used for the md system to set up RAID.

  The kernel source <file:///usr/src/linux> is, of course, the ultimate
  documentation. In other words, use the source, Luke.  It should also
  be pointed out that the kernel comes not only with source code which
  is even commented (well, partially at least) but also an informative
  documentation directory <file:///usr/src/linux/Documentation>.  If you
  are about to ask any questions about the kernel you should read this
  first, it will save you and many others a lot of time and possibly
  embarrassment.

  Also have a look in your system log file <file:///var/log/messages> to
  see what is going on and in particular how the booting went if too
  much scrolled off your screen. Using tail -f /var/log/messages in a
  separate window or screen will give you a continuous update of what is
  going on in your system.

  You can also take advantage of the /proc <file:///proc> file system
  that is a window into the inner workings of your system.  Use cat
  rather than more to view the files as they are reported as being zero
  length.

  Much of the work here is based on the Filesystem Structure Standard
  (FSSTND).  It has changed name to File Hierarchy Standard (FHS) and is
  less Linux specific.  The maintainer has set up a home page
  <http://www.pathname.com/fhs> which tells you how to join the
  currently private mailing list, where the development takes place.

  12.6.  Web pages

  There is a huge number of informative web pages out there and by their
  very nature they change quickly so don't be too surprised if these
  links become quickly outdated.

  ╖  Mike Neuffer, the author of the DPT caching RAID controller
     drivers, has some interesting pages on SCSI <http://www.uni-
     mainz.de/~neuffer/scsi> and DPT <http://www.uni-
     mainz.de/~neuffer/scsi/dpt>.

  ╖  Software RAID 1 development information can be found at RAID 1
     development page <http://www.nuclecu.unam.mx/~miguel/raid>.

  ╖  Disk related information on benchmarking, RAID, reliability and
     much, much more can be found at Linas Vepstas <http://linas.org>
     project page.

  ╖  Mark D. Roth has information on VPS
     <http://www.uiuc.edu/ph/www/roth>

  ╖  A similar kind of project on an Enhanced File System
     <http://www.virtual.net.au/~rjh/enh-fs.html>

  ╖  People who are awaiting support for VFAT32 and Joliet could have a
     look at the development page
     <http://bmrc.berkeley.edu/people/chaffee/index.html> for a preview.
     These drivers are now entering the 2.1.x kernel development series.

  For diagrams and information on all sorts of disk drives, controllers
  etc. both for current and discontinued lines The Ref
  <http://theref.c3d.rl.af.mil> is the site you need. There is a lot of
  useful information here, a real treasure trove.  You can also download
  the database using FTP <ftp://theref.c3d.rl.af.mil/public>.

  Please let me know if you have any other leads that can be of
  interest.

  12.7.  Search engines

  Remember you can also use the web search engines and that some, like

  ╖  Altavista <http://www.altavista.digital.com>

  ╖  Excite <http://www.excite.com>

  ╖  Hotbot <http://www.hotbot.com>

     can also search usenet news.

  Also remember that Dejanews <http://www.dejanews.com> is a dedicated
  news searcher that keeps a news spool from early 1995 and onwards.

  If you have to ask for help you are most likely to get help in the
  comp.os.linux.setup news group. Due to large workload and a slow
  network connection I am not able to follow that newsgroup so if you
  want to contact me you have to do so by e-mail.

  13.  Getting Help

  In the end you might find yourself unable to solve your problems and
  need help from someone else. The most efficient way is either to ask
  someone local or in your nearest Linux user group, search the web for
  the nearest one.

  Another possibility is to ask on Usenet News in one of the many, many
  newsgroups available. The problem is that these have such a high
  volume and noise (called low signal-to-noise ratio) that your question
  can easily fall through unanswered.

  No matter where you ask it is important to ask well or you will not be
  taken seriously. Saying just my disk does not work is not going to
  help you and instead the noise level is increased even further and if
  you are lucky someone will ask you to clarify.

  Instead you are recommended to describe your problems in some detail
  that will enable people to help you. The problem could lie somewhere
  you did not expect. Therefore you are advised to list up the following
  information on your system:

     Hardware

     ╖  Processor

     ╖  Chip set (Triton, Saturn etc)

     ╖  Bus (ISA, VESA, PCI etc)

     ╖  Expansion cards used (Disk controllers, video, io etc)

     Software

     ╖  BIOS (On motherboard and possibly SCSI host adapters)

     ╖  LILO, if used

     ╖  Linux kernel version as well as possible modifications and
        patches

     ╖  Kernel parameters, if any

     ╖  Software that shows the error (with version number or date)

     Peripherals

     ╖  Type of disk drives with manufacturer name, version and type

     ╖  Other relevant peripherals connected to the same busses

  As an example of how interrelated these problems are: an old chip set
  caused problems with a certain combination of video controller and
  SCSI host adapter.

  Remember that booting text is logged to /var/log/messages which can
  answer most of the questions above. Obviously if the drives fail you
  might not be able to get  the log saved to disk but you can at least
  scroll back up the screen using the SHIFT and PAGE UP keys. It may
  also be useful to include part of this in you request for help but do
  not go overboard, keep it brief as a complete log file dumped to
  Usenet News is more than a little annoying.

  14.  Concluding Remarks

  Disk tuning and partition decisions are difficult to make, and there
  are no hard rules here. Nevertheless it is a good idea to work more on
  this as the payoffs can be considerable. Maximizing usage on one drive
  only while the others are idle is unlikely to be optimal, watch the
  drive light, they are not there just for decoration. For a properly
  set up system the lights should look like Christmas in a disco. Linux
  offers software RAID but also support for some hardware base SCSI RAID
  controllers. Check what is available. As your system and experiences
  evolve you are likely to repartition and you might look on this
  document again. Additions are always welcome.

  14.1.  Coming Soon

  There are a few more important things that are about to appear here.
  In particular I will add more example tables as I am about to set up
  two fairly large and general systems, one at work and one at home.
  These should give some general feeling on how a system can be set up
  for either of these two purposes. Examples of smooth running existing
  systems are also welcome.

  There is also a fair bit of work left to do on the various kinds of
  file systems and utilities.

  There will be a big addition on drive technologies coming soon as well
  as a more in depth description on using fdisk or cfdisk.  The file
  systems will be beefed up as more features become available as well as
  more on RAID and what directories can benefit from what RAID level.

  Recently I received an information pack from DPT, who made the first
  hardware RAID supported by Linux. Their leaflets now carry the
  familiar penguin logo to show they support Linux. More in-depth
  information will come soon.

  There is some minor overlapping with the Linux Filesystem Structure
  Standard that I hope to integrate better soon, which will probably
  mean a big reworking of all the tables at the end of this document.
  When the new version is released there will be a substantial rewrite
  of some of the sections in this HOWTO but no release date has been
  announced yet.

  When the new standard appear various details such as directory names,
  sizes and file placements will be changed.

  I have made the assumption that the first partition starts at track 0
  and that this track is the innermost track. That, however, is looking
  more and more like an unwarranted assumption, and not only because of
  the logical re-mapping that takes place. More on this when information
  becomes available.

  As more people start reading this I should get some more comments and
  feedback. I am also thinking of making a program that can automate a
  fair bit of this decision making process and although it is unlikely
  to be optimum it should provide a simpler, more complete starting
  point.

  14.2.  Request for Information

  It has taken a fair bit of time to write this document and although
  most pieces are beginning to come together there are still some
  information needed before we are out of the beta stage.

  ╖  More information on swap sizing policies is needed as well as
     information on the largest swap size possible under the various
     kernel versions.

  ╖  How common is drive or file system corruption? So far I have only
     heard of problems caused by flaky hardware.

  ╖  References to speed and drives is needed.

  ╖  Are any other Linux compatible RAID controllers available?

  ╖  Leads to file system, volume management and other related software
     is welcome.

  ╖  What relevant monitoring, management and maintenance tools are
     available?

  ╖  General references to information sources are needed, perhaps this
     should be a separate document?

  ╖  Usage of /tmp and /var/tmp has been hard to determine, in fact what
     programs use which directory is not well defined and more
     information here is required. Still, it seems at least clear that
     these should reside on different physical drives in order to
     increase parallelicity.

  14.3.  Suggested Project Work

  Now and then people post on comp.os.linux.*, looking for good project
  ideas. Here I will list a few that comes to mind that are relevant to
  this document. Plans about big projects such as new file systems
  should still be posted in order to either find co-workers or see if
  someone is already working on it.

     Planning tools
        that can automate the design process outlines earlier would
        probably make a medium sized project, perhaps as an exercise in
        constraint based programming.

     Partitioning tools
        that take the output of the previously mentioned program and
        format drives in parallel and apply the appropriate symbolic
        links to the directory structure. It would probably be best if
        this were integrated in existing system installation software.
        The drive partitioning setup used in Solaris is an example of
        what it can look like.

     Surveillance tools
        that keep an eye on the partition sizes and warn before a
        partition overflows.

     Migration tools
        that safely lets you move old structures to new (for instance
        RAID) systems. This could probably be done as a shell script
        controlling a back up program and would be rather simple. Still,
        be sure it is safe and that the changes can be undone.

  15.  Questions and Answers

  This is just a collection of what I believe are the most common
  questions people might have. Give me more feedback and I will turn
  this section into a proper FAQ.

  ╖  Q:How many physical disk drives (spindles) does a Linux system
     need?

     A: Linux can run just fine on one drive (spindle).  Having enough
     RAM (around 32 MB, and up to 64 MB) to support swapping is a better
     price/performance choice than getting a second disk.  (E)IDE disk
     is usually cheaper (but a little slower) than SCSI.

  ╖  Q: I have a single drive, will this HOWTO help me?

     A: Yes, although only to a minor degree. Still, the section on
     ``Physical Track Positioning'' will offer you some gains.

  ╖  Q: Are there any disadvantages in this scheme?

     A: There is only a minor snag: if even a single partition overflows
     the system might stop working properly. The severity depends of
     course on what partition is affected. Still this is not hard to
     monitor, the command df gives you a good overview of the situation.
     Also check the swap partition(s) using free to make sure you are
     not about to run out of virtual memory.

  ╖  Q: OK, so should I split the system into as many partitions as
     possible for a single drive?

     A: No, there are several disadvantages to that. First of all
     maintenance becomes needlessly complex and you gain very little in
     this. In fact if your partitions are too big you will seek across
     larger areas than needed.  This is a balance and dependent on the
     number of physical drives you have.

  ╖  Q: Does that mean more drives allows more partitions?

     A: To some degree, yes. Still, some directories should not be split
     off from root, check out the file system standard (soon released
     under the name File Hierarchy Standard) for more details.

  ╖  Q: What if I have many drives I want to use?

     A: If you have more than 3-4 drives you should consider using RAID
     of some form. Still, it is a good idea to keep your root partition
     on a simple partition without RAID, see the section on ``RAID'' for
     more details.

  ╖  Q: I have installed the latest Windows95 but cannot access this
     partition from within the Linux system, what is wrong?

     A: Most likely you are using FAT32 in your windows partition. It
     seems that Microsoft decided we needed yet another format, and this
     was introduced in their latest version of Windows95. The advantage
     is that this format is better suited to large drives. Unfortunately
     there is no stable driver for Linux out yet . A test version is out
     but not yet in the standard kernel.

     You might also be interested to hear that Microsoft NT 4.0 does not
     support it yet either.

     Until a stable version is available you can avoid this problem by
     installing Windows95 over an existing FAT16 partition, made for
     instance by an older installation of DOS. This forces the Windows95
     to use FAT16 which is supported by Linux.

  ╖  Q: I cannot get the disk size and partition sizes to match,
     something is missing. What has happened?

     It is possible you have mounted a partition onto a mount point that
     was not an empty directory. Mount points are directories and if it
     is not empty the mounting will mask the contents. If you do the
     sums you will see the amount of disk space used in this directory
     is missing from the observed total.

     To solve this you can boot from a rescue disk and see what is
     hiding behind your mount points and remove or transfer the contents
     by mounting th offending partition on a temporary mounting point.
     You might find it useful to have "spare" emergency mounting points
     ready made.

  ╖  Q: What is this nyx that is mentioned several times here?

     A: It is a large free Unix system with currently about 10000 users.
     I use it for my web pages for this HOWTO as well as a source of
     ideas for a setup of large Unix systems. It has been running for
     many years and has a quite stable setup. For more information you
     can view the Nyx homepage <http://www.nyx.net> which also gives you
     information on how to get your own free account.

  16.  Bits and Pieces

  This is basically a section where I stuff all the bits I have not yet
  decided where should go, yet that I feel is worth knowing about. It is
  a kind of transient area.

  16.1.  Combining swap and /tmp

  Recently there have been discussions in the various linux related news
  groups about specialized file systems for temporary storage.  This is
  partly inspired by the tmpfs on *BSD* and Solaris, as well as swapfs
  on the NeXT machines.

  The rationale is that these are temporary storage that normally does
  not require much space, yet in normal systems you need to reserve a
  certain amount of space for these. Elementary statistical knowledge
  tells you (very simplified) that when you sum a number of variables
  the relative statistical uncertainty decreases. So combining swap and
  /tmp you do not need to reserve as much space as you otherwise would
  need.

  This specialized file system is nothing more than a swappable RAM disk
  that are swapped out to disk when and only when space is limited, thus
  effectively putting temporary files on the swap partition.

  There is, however, a snag. This scheme prevents you from getting
  parallel activity on swap and /tmp drives so under heavy activity the
  system takes a bigger performance hit. Put another way, you trade
  speed to get space. Interleaving across multiple drives reduces this
  somewhat.

  16.2.  Interleaved swap drives.

  This is not striping across several drives, instead drives are
  accessed in a round robin fashion in order to spread the load in a
  crude fashion.  In Linux you additionally have a priority parameter
  you can adjust for tuning your system, especially useful if your disks
  differs  significantly in speed. Check man 8 swapon as well as man 2
  swapon for more information.

  16.3.  Swap partition: to use or not to use

  In many cases you do not need a swap partition, for instance if you
  have plenty of RAM, say, more than 64MB, and you are the sole user of
  the machine. In this case you can experiment running without a swap
  partition and check the system logs to see if you ran out of virtual
  memory at any point.

  Removing swap partitions have two advantages:

  ╖  you save disk space (rather obvious really)

  ╖  you save seek time as swap partitions otherwise would lie in the
     middle of your disk space.

  In the end, having a swap partition is like having a heated toilet:
  you do not use it very often, but you sure appreciate it when you
  require it.

  16.4.  Mount point and /mnt

  In an earlier version of this document I proposed to put all
  permanently mounted partitions under /mnt. That, however, is not such
  a good idea as this itself can be used as a mount point, which leads
  to all mounted partitions becoming unavailable. Instead I will propose
  mounting straight from root using a meaningful name like
  /mnt.descriptive-name.

  Lately I have become aware that some Linux distributions use mount
  points at subdirectories under /mnt, such as /mnt/floppy and
  /mnt/cdrom, which just shows how confused the whole issue is.
  Hopefully FHS should clarify this.

  16.5.  SCSI id numbers and names

  Partitions are labeled in the order they are found, not depending on
  the SCSI id number. This means that if you add a drive with an id
  number inserted in the previous order of numbers, or change id number
  in any other way, the partition names will be messed up. This is
  important if you use removable media. In order to save yourself from
  some unpleasant experiences, you are recommended to use low numbers
  for fixed media and reserve the last number(s) for removable media
  drives.

  Many have been bitten by this misfeature and there is a strong call
  for something to be done about it. Nobody knows how soon this will be
  fixed so in the meantime it is wise to take this into consideration
  when you design your system. For instance it may be a good idea to use
  the lowest SCSI id number for you root disk so that it has the least
  probability of being renumbered should one drive fail.

  16.6.  Power and Heating

  Not many years ago a machine with the equivalent power of a modern PC
  required 3-phase power and cooling, usually by air conditioning the
  machine room but some times also by water cooling. Technology has
  progressed very quickly giving not only high speed but also low power
  components. Still, there is a definite limit to the technology,
  something one should keep in mind as the system is expanded with yet
  another disk drive or PCI card. When the power supply is running at
  full rated power, keep in mind that all this energy is going
  somewhere, mostly into heat. Unless this is dissipated using fans you
  will get a serious heating inside the cabinet followed by a reduced
  reliability and also life time of the electronics.  Manufacturers
  state minimum cooling requirements for their drives, usually in terms
  of cubic feet per minute (CFM). You are well advised to take this
  serious.

  Keep air flow passages open, clean out dust and check the temperature
  of your system running. If it is too hot to touch it is probably
  running too hot.

  If possible use sequential spin up for the drives. It is during spin
  up, when the drive platters accelerate up to normal speed, that a
  drive consumes maximum power and if all drives start up simultaneously
  you could go beyond the rated power maximum of your power supply.

  16.7.  Dejanews

  This is an Internet system that no doubt most of you are familiar
  with.  It searches and serves Usenet News articles from 1995 and to
  the latest postings and also offers a web based reading and posting
  interface.  There is a lot more, check out Dejanews
  <http://www.dejanews.com> for more information.

  What perhaps is less known, is that they use about 20 Linux SMP
  computers each of which uses the md module to manage between 4 and 24
  Gig of disk space (over 150 Gig altogether) for this service.  The
  system is continuously growing but at the time of writing they use
  mostly dual Pentium Pro 200MHz systems with 256M RAM.

  A production machine normally has 1 disk for the operating system and
  between 4 and 6 disks managed by the md module where the articles are
  archived.  The drives are connected to BusLogic Model BT-946C PCI SCSI
  adapters, usually two to a machine.

  Just in case: this is not an advertisement, it is stated as an example
  of how much is required for what is a major Internet service.

  16.8.  File system structure

  There are many file system structures in existence, differing with
  FSSTND (and soon FHS) to varying degree both in terms of philosophy,
  strategy and implementation. It is not possible to detail all here,
  instead the interested reader should read the relevant manual page,
  man hier which is available on many platforms and implementations.

  16.9.  Track numbering and optimizing schemes

  In the old days the file system used to take advantage of knowing the
  physical drive parameters in order to optimize transfers, for instance
  by endeavouring to keep a file within a single track if possible which
  saves track-to-track seek time. These days with logical drive
  parameters, drive cache and schemes to map out bad sectors, such
  optimizations become meaningless and might even cost more than it
  would gain. As most Linux installations use modern file systems these
  schemes are not used, however, some other operating systems have
  retained such schemes.

  17.  Appendix A: Partitioning layout table: mounting and linking

  The following table is designed to make layout a simpler paper and
  pencil exercise. It is probably best to print it out (using NON
  PROPORTIONAL fonts) and adjust the numbers until you are happy with
  them.

  Mount point is what directory you wish to mount a partition on or the
  actual device. This is also a good place to note how you plan to use
  symbolic links.

  The size given corresponds to a fairly big Debian 1.2.6 installation.
  Other examples are coming later.

  Mainly you use this table to select what structure and drives you will
  use, the partition numbers and letters will come from the next two
  tables.

  Directory       Mount point     speed   seek    transfer        size    SIZE

  swap            __________      ooooo   ooooo   ooooo           32      ____

  /               __________      o       o       o               20      ____

  /tmp            __________      oooo    oooo    oooo                    ____

  /var            __________      oo      oo      oo              25      ____
  /var/tmp        __________      oooo    oooo    oooo                    ____
  /var/spool      __________                                              ____
  /var/spool/mail __________      o       o       o                       ____
  /var/spool/news __________      ooo     ooo     oo                      ____
  /var/spool/____ __________      ____    ____    ____                    ____

  /home           __________      oo      oo      oo                      ____

  /usr            __________                                      500     ____
  /usr/bin        __________      o       oo      o               250     ____
  /usr/lib        __________      oo      oo      ooo             200     ____
  /usr/local      __________                                              ____
  /usr/local/bin  __________      o       oo      o                       ____
  /usr/local/lib  __________      oo      oo      ooo                     ____
  /usr/local/____ __________                                              ____
  /usr/src        __________      o       oo      o               50      ____

  DOS             __________      o       o       o                       ____
  Win             __________      oo      oo      oo                      ____
  NT              __________      ooo     ooo     ooo                     ____

  /mnt._________  __________      ____    ____    ____                    ____
  /mnt._________  __________      ____    ____    ____                    ____
  /mnt._________  __________      ____    ____    ____                    ____
  /_____________  __________      ____    ____    ____                    ____
  /_____________  __________      ____    ____    ____                    ____
  /_____________  __________      ____    ____    ____                    ____

  Total capacity:

  18.  Appendix B: Partitioning layout table: numbering and sizing

  This table follows the same logical structure as the table above where
  you decided what disk to use. Here you select the physical tracking,
  keeping in mind the effect of track positioning mentioned earlier in
  ``Physical Track Positioning''.

  The final partition number will come out of the table after this.

    Drive           sda     sdb     sdc     hda     hdb     hdc     ___

  SCSI ID         |  __   |  __   |  __   |

  Directory
  swap            |       |       |       |       |       |       |

  /               |       |       |       |       |       |       |

  /tmp            |       |       |       |       |       |       |

  /var            :       :       :       :       :       :       :
  /var/tmp        |       |       |       |       |       |       |
  /var/spool      :       :       :       :       :       :       :
  /var/spool/mail |       |       |       |       |       |       |
  /var/spool/news :       :       :       :       :       :       :
  /var/spool/____ |       |       |       |       |       |       |

  /home           |       |       |       |       |       |       |

  /usr            |       |       |       |       |       |       |
  /usr/bin        :       :       :       :       :       :       :
  /usr/lib        |       |       |       |       |       |       |
  /usr/local      :       :       :       :       :       :       :
  /usr/local/bin  |       |       |       |       |       |       |
  /usr/local/lib  :       :       :       :       :       :       :
  /usr/local/____ |       |       |       |       |       |       |
  /usr/src        :       :       :       :

  DOS             |       |       |       |       |       |       |
  Win             :       :       :       :       :       :       :
  NT              |       |       |       |       |       |       |

  /mnt.___/_____  |       |       |       |       |       |       |
  /mnt.___/_____  :       :       :       :       :       :       :
  /mnt.___/_____  |       |       |       |       |       |       |
  /_____________  :       :       :       :       :       :       :
  /_____________  |       |       |       |       |       |       |
  /_____________  :       :       :       :       :       :       :

  Total capacity:

  19.  Appendix C: Partitioning layout table: partition placement

  This is just to sort the partition numbers in ascending order ready to
  input to fdisk or cfdisk. Here you take physical track positioning
  into account when finalizing your design. Unless you get specific
  information otherwise, you can assume track 0 is the outermost track.

  These numbers and letters are then used to update the previous tables,
  all of which you will find very useful in later maintenance.

  In case of disk crash you might find it handy to know what SCSI id
  belongs to which drive, consider keeping a paper copy of this.

          Drive :   sda     sdb     sdc     hda     hdb     hdc     ___

  Total capacity: |  ___  |  ___  |  ___  |  ___  |  ___  |  ___  |  ___
  SCSI ID         |  __   |  __   |  __   |

  Partition

  1               |       |       |       |       |       |       |
  2               :       :       :       :       :       :       :
  3               |       |       |       |       |       |       |
  4               :       :       :       :       :       :       :
  5               |       |       |       |       |       |       |
  6               :       :       :       :       :       :       :
  7               |       |       |       |       |       |       |
  8               :       :       :       :       :       :       :
  9               |       |       |       |       |       |       |
  10              :       :       :       :       :       :       :
  11              |       |       |       |       |       |       |
  12              :       :       :       :       :       :       :
  13              |       |       |       |       |       |       |
  14              :       :       :       :       :       :       :
  15              |       |       |       |       |       |       |
  16              :       :       :       :       :       :       :

  20.  Appendix D: Example: Multipurpose server

  The following table is from the setup of a medium sized multipurpose
  server where I work. Aside from being a general Linux machine it will
  also be a network related server (DNS, mail, FTP, news, printers etc.)
  X server for various CAD programs, CD ROM burner and many other
  things.  The files reside on 3 SCSI drives with a capacity of 600,
  1000 and 1300 MB.

  Some further speed could possibly be gained by splitting /usr/local
  from the rest of the /usr system but we deemed the further added
  complexity would not be worth it. With another couple of drives this
  could be more worthwhile. In this setup drive sda is old and slow and
  could just a well be replaced by an IDE drive. The other two drives
  are both rather fast. Basically we split most of the load between
  these two. To reduce dangers of imbalance in partition sizing we have
  decided to keep /usr/bin and /usr/local/bin in one drive and /usr/lib
  and /usr/local/lib on another separate drive which also affords us
  some drive parallelizing.

  Even more could be gained by using RAID but we felt that as a server
  we needed more reliability than was then afforded by the md patch and
  a dedicated RAID controller was out of our reach.

  21.  Appendix E: Example: mounting and linking

  Directory       Mount point     speed   seek    transfer        size    SIZE

  swap            sdb2, sdc2      ooooo   ooooo   ooooo           32      2x64

  /               sda2            o       o       o               20       100

  /tmp            sdb3            oooo    oooo    oooo                     300

  /var            __________      oo      oo      oo                      ____
  /var/tmp        sdc3            oooo    oooo    oooo                     300
  /var/spool      sdb1                                                     436
  /var/spool/mail __________      o       o       o                       ____
  /var/spool/news __________      ooo     ooo     oo                      ____
  /var/spool/____ __________      ____    ____    ____                    ____

  /home           sda3            oo      oo      oo                       400

  /usr            sdb4                                            230      200
  /usr/bin        __________      o       oo      o               30      ____
  /usr/lib        -> libdisk      oo      oo      ooo             70      ____
  /usr/local      __________                                              ____
  /usr/local/bin  __________      o       oo      o                       ____
  /usr/local/lib  -> libdisk      oo      oo      ooo                     ____
  /usr/local/____ __________                                              ____
  /usr/src        ->/home/usr.src o       oo      o               10      ____

  DOS             sda1            o       o       o                        100
  Win             __________      oo      oo      oo                      ____
  NT              __________      ooo     ooo     ooo                     ____

  /mnt.libdisk    sdc4            oo      oo      ooo                      226
  /mnt.cd         sdc1            o       o       oo                       710

  Total capacity: 2900 MB

  22.  Appendix F: Example: numbering and sizing

  Here we do the adjustment of sizes and positioning.

  Directory         sda     sdb     sdc

  swap            |       |   64  |   64  |

  /               |  100  |       |       |

  /tmp            |       |  300  |       |

  /var            :       :       :       :
  /var/tmp        |       |       |  300  |
  /var/spool      :       :  436  :       :
  /var/spool/mail |       |       |       |
  /var/spool/news :       :       :       :
  /var/spool/____ |       |       |       |

  /home           |  400  |       |       |

  /usr            |       |  200  |       |
  /usr/bin        :       :       :       :
  /usr/lib        |       |       |       |
  /usr/local      :       :       :       :
  /usr/local/bin  |       |       |       |
  /usr/local/lib  :       :       :       :
  /usr/local/____ |       |       |       |
  /usr/src        :       :       :       :

  DOS             |  100  |       |       |
  Win             :       :       :       :
  NT              |       |       |       |

  /mnt.libdisk    |       |       |  226  |
  /mnt.cd         :       :       :  710  :
  /mnt.___/_____  |       |       |       |

  Total capacity: |  600  | 1000  | 1300  |

  23.  Appendix G: Example: partition placement

  This is just to sort the partition numbers in ascending order ready to
  input to fdisk or cfdisk. Remember to optimize for physical track
  positioning (not done here).

               Drive :   sda     sdb     sdc

       Total capacity: |   600 |  1000 |  1300 |

       Partition

       1               |   100 |   436 |   710 |
       2               :   100 :    64 :    64 :
       3               |   400 |   300 |   300 |
       4               :       :   200 :   226 :

  24.  Appendix H: Example II

  The following is an example of a server setup in an academic setting,
  and is contributed by nakano (at) apm.seikei.ac.jp. I have only done
  minor editing to this section.

  /var/spool/delegate is a directory for storing logs and cache files of
  an WWW proxy server program, "delegated". Since I don't notice it
  widely, there are 1000--1500 requests/day currently, and average disk
  usage is 15--30% with expiration of caches each day.

  /mnt.archive is used for data files which are big and not frequently
  referenced such a s experimental data (especially graphic ones),
  various source archives, and Win95 backups (growing very fast...).

  /mnt.root is backup root file system containing rescue utilities. A
  boot floppy is also prepared to boot with this partition.

  =================================================
  Directory               sda      sdb     hda

  swap                    |    64 |    64 |       |
  /                       |       |       |    20 |
  /tmp                    |       |       |   180 |

  /var                    :   300 :       :       :
  /var/tmp                |       |   300 |       |
  /var/spool/delegate     |   300 |       |       |

  /home                   |       |       |   850 |
  /usr                    |   360 |       |       |
  /usr/lib                -> /mnt.lib/usr.lib
  /usr/local/lib          -> /mnt.lib/usr.local.lib

  /mnt.lib                |       |   350 |       |
  /mnt.archive            :       :  1300 :       :
  /mnt.root               |       |    20 |       |

  Total capacity:            1024    2034    1050

  =================================================
          Drive :           sda     sdb     hda
  Total capacity:         |  1024 |  2034 |  1050 |

  Partition
  1                       |   300 |    20 |    20 |
  2                       :    64 :  1300 :   180 :
  3                       |   300 |    64 |   850 |
  4                       :   360 :   ext :       :
  5                       |       |   300 |       |
  6                       :       :   350 :       :

  Filesystem         1024-blocks  Used Available Capacity Mounted on
  /dev/hda1              19485   10534     7945     57%   /
  /dev/hda2             178598      13   169362      0%   /tmp
  /dev/hda3             826640  440814   343138     56%   /home
  /dev/sda1             306088   33580   256700     12%   /var
  /dev/sda3             297925   47730   234807     17%   /var/spool/delegate
  /dev/sda4             363272  170872   173640     50%   /usr
  /dev/sdb5             297598       2   282228      0%   /var/tmp
  /dev/sdb2            1339248  302564   967520     24%   /mnt.archive
  /dev/sdb6             323716   78792   228208     26%   /mnt.lib

  Apparently /tmp and /var/tmp is too big. These directories shall be
  packed together into one partition when disk space shortage comes.

  /mnt.lib is also seemed to be, but I plan to install newer TeX and
  ghostscript archives, so /usr/local/lib may grow about 100M or so
  (since we must use Japanese fonts!).

  Whole system is backed up by Seagate Tapestore 8000 (Travan TR-4,
  4G/8G).

  25.  Appendix I: Example III: SPARC Solaris

  The following section is the basic design used at work for a number of
  Sun SPARC servers running Solaris 2.5.1 in an industrial development
  environment. It serves a number of database and cad applications in
  addition to the normal services such as mail.

  Simplicity is emphasized here so /usr/lib has not been split off from
  /usr.

  This is the basic layout, planned for about 100 users.

          Drive:        SCSI 0                      SCSI 1

          Partition     Size (MB)   Mount point    Size (MB)   Mount point

            0           160         swap           160         swap
            1           100         /tmp           100         /var/tmp
            2           400         /usr
            3           100         /
            4            50         /var
            5
            6           remainder   /local0        remainder   /local1

  Due to specific requirements at this place it is at times necessary to
  have large partitions available on a short notice. Therefore drive 0
  is given as many tasks as feasible, leaving a large /local1 partition.

  This setup has been in use for some time now and found satisfactorily.

  For a more general and balanced system it would be better to swap /tmp
  and /var/tmp and then move /var to drive 1.